0
Want this question answered?
Be notified when an answer is posted
Add your answer:
Earn +20 pts
What is a 15 amp double pole breaker?
A double pole breaker has one pole attached to one side of your breaker panel's bus or hot leg, and another pole attached to another hot leg or bus, if it is in a residential panel (in the US) each leg of the breaker is 120 volts to ground or neutral and 240 hot leg to hot leg. The 15 amp indicates that the breaker will trip if the circuit exceeds 15 amps across the two outputs of the breaker.
Which terminal on a 15 amp household breaker does the hot wire feed into and which one does it come out?
On a 15 amp household breaker there is no terminal on the in feed of the breaker. The breaker either plugs into the distribution panel's bus bar or it bolts to the distribution's bus bars. The feed conductor connects to the load side of the breaker at its terminal lug.
What is the purpose of bus coupler for the LT panel?
The bus coupler is used to couple one bus to the other without interruption in power supply. It uses the help of the circuit breaker and isolators to achieve this without creating hazardous arcs.
How can you wire a normal 120V outlet out of a double pole circuit breaker?
well, the easy answer is, black wire to one pole of the breaker, white wire to the neutral bus with all the other white wires, bare wire to the ground bus with all the other bare (or green) wires. BUT the breaker must be 20 amps or less for residential outlets and you much match the wire size to the breaker, #14 for 15 amp breaker, #12 for a 20 amp breaker AND if there is only going to be one outlet, if it is a 20 amp circuit, the outlet has to be rated for 20 amps. Yes, but why would you want to? It is unclear to anybody else what you are doing and therefore a hazard. Do it right. Use a single pole breaker designed for 110V.
How do you tell that is a 220v or 110v motor?
The 220-240 VAC breaker must span both bus bars in the panel. Therefore it is either double the height (top to bottom - usual circumstance) or double the width (side to side in some older boxes).
What are the types of bus bar arrangements?
Single bus is used in smaller, less important substations. A fault on the bus requires tripping of all lines into the bus. When higher redundancy is necessary, ring and breaker and 1/2 schemes are used. These are the three most common.
What is a 15 amp double pole breaker?
A double pole breaker has one pole attached to one side of your breaker panel's bus or hot leg, and another pole attached to another hot leg or bus, if it is in a residential panel (in the US) each leg of the breaker is 120 volts to ground or neutral and 240 hot leg to hot leg. The 15 amp indicates that the breaker will trip if the circuit exceeds 15 amps across the two outputs of the breaker.
What type panel does a 4 pole breaker require?
The panel and breaker have to be of the same manufacturer. This way the breaker will fit into the panel. If the panel has a push in bus bar, the breaker must also be the type to accept the bus bar. If the bus bars in the panel are of the bolt in type then the breaker also has to be a bolt in breaker.
What is the difference between a 100 amp breaker box and a 125 breaker box?
The amperage capacity of the main bus bars and the connection of the main breaker to the bus bars.
Do you need a 20 amp single or double pole breaker for your washer?
Washing machines in the U.S. operate on 120 volts. That requires a single pole 20 amp breaker and wired with 12/2 w-ground wire. Black to the breaker, white to the neutral bus bar, and copper ground to the ground bus bar.
What is bus section?
Bus section is a device is used to separating a bus into two. So if got any fault in right hand side just open the circuit breaker in the bus section and do maintenance without shut down the whole thing.
Which terminal on a 15 amp household breaker does the hot wire feed into and which one does it come out?
On a 15 amp household breaker there is no terminal on the in feed of the breaker. The breaker either plugs into the distribution panel's bus bar or it bolts to the distribution's bus bars. The feed conductor connects to the load side of the breaker at its terminal lug.
What is the purpose of bus coupler for the LT panel?
The bus coupler is used to couple one bus to the other without interruption in power supply. It uses the help of the circuit breaker and isolators to achieve this without creating hazardous arcs.
Bus bar arrangements in sub station?
Burbars are the important elements in the electrical substation. Bus bars acts as nodal point in the substation which connects different incoming and outgoing circuits.Substations present in the power system performs various operations depends on the application such as stepping up the voltage, stepping down the voltage, high voltage transmission and switching stations to route the power to desired load center.Busbars in Substation:Busbars used in the substations are generally rectangular or circular cross section bars. These busbars can be either solid or hollow structures. Hollow circular cross section busbars are employes in EHV substations to reduce the corona effect.Switching Schemes:Switching schemes implies different methods employed to connect electrical circuits in the power system to transfer the electrical power in reliable manner. Switching schemes helps in deliver the electrical power to power system if any part of the system is faulty or under maintenance.Substations use different types of busbar arrangements or switching schemes depends upon the application, reliability of the supply and cost of installation. In every substations busbars plays a common role to connect different circuits. However switching is possible in the power system with the help of circuit breakers and isolators.Considerations for selection of busbar arrangement:Different types of busbar arrangements are employed based on the voltage, reliability of the supply, flexibility in transmitting power and cost. The other aspects considering in designing the busbars arrangements are:Simplicity in the designMaintenance of different elements without interruption in the power supplyFuture expansion feasibilityEconomical in cost of installation and operationDifferent busbar arrangements:Some of the switching schemes are busbar arrangements employed in the substations are listed below:Single Bus-bar arrangementDouble Main Bus-bar schemeMain and Transfer bus-bar schemeOne and half breaker schemeRing Main arrangement schemeSingle Bus-bar scheme:This is the simplest busbar scheme available which consists of single set of busbars connected to the generators, transformers and load feeders. All the feeders are connected by circuit breaker and set of isolators. This arrangement helps to remove the connecting elements (Generators, transformers, etc ) for maintenance by opening the circuit breaker contacts and further opening the isolators.Advantages:This busbar arrangement enjoys less cost of installationLess maintenancesimple operationDisadvantages:Fault on the busbar all the feeders connected to the busbars should be disconnectedwhen Busbar is under maintenance total supply and all feeders should be disconnectedLeast flexibility and reliabilitySee all 5 photosSingle busbar SchemeDouble Main Busbar Scheme:Normally in double main busbar scheme each circuit is connected to both the buses. In some cases half of the circuits can be connected and operated on each bus, in these cases bus or circuit breaker failure would cause loss to half of the circuits. In double main busbar arrangement one or two breakers can be provided for each circuit. Double main busbar and double breaker scheme provides high reliability in the case of fault or outage of one of the breaker.Advantages:Any circuit can be taken out of circuit for maintenanceFlexibility in connecting the feeder circuit to either of the busbarsDisadvantages:Most expensiveLoose circuits connected to busbar when fault occurs on the busbarDouble Busbar Single Breaker SchemeMain and Transfer Busbar SchemeMain and Transfer busbar scheme is similiar to single busbar arrangement with additional transfer bus connected. Tie circuit breaker is provided to tie both the main and transfer bus. During normal operation all the circuits are connected to the main bus. When circuit breaker connected to the circuit (transmission line) is required to trip for maintenance, tie circuit breaker connecting the main and transfer bus is closed. The relay protection for the circuits connected to the transfer bus is taken care by the tie circuit breaker.Advantages:Low initial costAny breaker can be taken of circuit for maintenanceDisadvantages:Requires one extra breaker for bus tieSwitching is somewhat complicated when breaker is under maintenanceMain and Transfer Busbar SchemeOne and Half breaker Busbar scheme:In One and half breaker scheme, two circuits are connected between the three circuit breakers. Hence One and Half breaker name was coined for this type of arrangement. Under normal operating conditions all the breakers are closed and both the busbars are energized. Any Circuit fault will trip two circuit breakers and no other circuit will be affected in this arrangement. When a busbar fault occur only breakers adjacent to busbars trips and no circuit will loose power. Two busbars can also be taken out of service with out affecting the power flow if the power source circuit ( alternator circuit) and receiving circuit (transmission line) available in the same bay.Advantages:Most flexible operation possibleHigh reliabilityBus failure will not remove any circuit from serviceDisadvantages:High costRelaying is somewhat complicated since the middle breaker must responsible for both the circuits on either direction and should operateone and Half Breaker SchemeRing busbar schemeIn this ring main busbar scheme arrangement, breakers are connected in ring and circuits are connected between the breakers. There will be same number of circuits as the number of breakers in the arrangement. During normal operation all the breakers are closed. During circuit fault two breakers connecting the circuit trips. During breaker maintenance the ring is broken but all the lines remain in service.Advantages:Low costFlexible operation for breaker maintenanceAny breaker can be taken out of service without interrupting loadPower can be fed from both the directionDisadvantages:Fault occur during maintenance will break the ringRelaying is complexBreaker failure during fault will trip one additional circuitRing Main Busbar Scheme
A Main panel that can have more breakers installed if it had morelonger hot bus. the question is is this an option are hot buses replaceable?
No, If the breaker bus is replace with a larger breaker bus you will then void the manufactures warranty and the UL listing of that box for electrical safety.
How long is a double decker bus?
as long as a double decker bus
Can a generator be motored simply by closing generator breaker to energized bus?
No.
