0
Just curious
Wiki User
∙ 14y ago
Add your answer:
Earn +20 pts
How do you make a MTD Lawn machine mower a dually?
Take a metal pipe a wide one and weld it to the rim of the other tire... center it and then weld the other side to other rim... have hollor solid pipe so u can put on and take off
How do you make reducer from pipe?
By placing a smaller pipe insider the larger one and weld /braze the gap
What is the difference between a Butt weld and a socket weld?
A butt weld is where the diameter of the pipes welded together are the same, a socket weld is where a larger diameter pipe is fitted into a smaller one. In making a butt weld, the pipes (or pipe and fitting) usually have an angle machined or ground into the outside corner, so when they are placed together face-face, there is a circumferential V shaped gap serving as the weld prep. In a socket weld, the pipe is inserted into the socket, backed off slightly to make a gap between the end of the pipe and the bottom of the socket, and the weld is made around the outside diameter of the socket to the outside diameter of the pipe. The gap at the bottom of the pipe prevents thermal expansion from stressing the joint during or after welding.
Where can you purchase just the flex pipe for a 1995 Camry?
A GOOD MUFFLER SHOP LIKE MEINEKE CAN CUT OUT THE BAD SECTION OF FLEX PIPE AND WELD IN A NEW ONE. USUALLY TH PIPE IS AS GOOD OR BETTER THAN NEW.
How much liter of glue require for one meter of pipe?
The amount of glue that you use on pipe depends on the number of joints or fittings - not length of pipe. - One litre is a lot of pipe glue ! -I have done thousands of feet of PVC pipe and fittings this past year, and still have some glue left in my litre can of Weld-On 711.
How can one weld a flange tight?
One would weld a flange tight by firstly establishing which type of joint they were welding. One of the most common is welding a neck flange. For this you would need to ensure that both pieces of material to be welded are melted on the first bead of the weld. You would continue around the pipe until you reach the beginning. Once back at the start you need to ensure that the final bead is higher than the joint being welded. The weld should be approximately 1/16th of and in to 1/8th of and inch from the pipe to the flange.
How do you fit Yamaha r1 muffler to Yamaha r6?
make a piece of tapered pipe to fit from one muffler to the other then weld them together.
What is take off measurement for 90 degree 8 inch pipe?
The take-off for a standard radius 90 is one and one half the diameter of the pipe. Example: 6 inch 90 has a take- off of 9 inches. The take-off for short radius 90 would be the dia. of the pipe. Long radius 90 is 2 times the pipe diameter.
If you own a 43cc gas scooter is there some way to build your own exhaust pipe and how would you attach one that you have built yourself?
maybe u could try and use some copper tubing you could cut the flange off your old pipe and weld it to your homade pipe. make a manifold by tracing the stock pipe and then trace it on some 1/8in steel and cut it out with a jigsaw, tourch, plazmacutter or what ever you have then drill holes for the bolts. mount that on the engine then find yourself a pice of tubeing that fits the manifold and tack weld it on, take it off the engine then fully weld it. or gut the stock pipe and drill out the outlet to have a tuned exhaust pipe make your pipe bolt it on, use house paint and paint your exhaust(it dousn't matter of the colour trust me) ... wait until dry and start your bike there will be a nice ring burnt off your exhaust, mark and cut there ...now take off all the paint and now you have a preformanced tuned exhaust
How do you remove broken exhaust pipe from muffler pipe?
If it is welded on, you can grind away at the weld until it either falls off, or you see what appears to be a crack all around the weld ( you can then pry it off). If it is clamped on, then you should just have to beat the rust away with a hammer and chisel. But really, mufflers are so cheap you should just get a new one.
TIG weld Testing Techniques How do you test TIG welding on a CuNi Pipe section?
One method is Ultra Sonic Sound, another Die Penetration.
I need to know the take off for a one inch butt weld ninety. is it one and a half time the size of the pipe.?
1.5in For a 90 degree butt-joint each piece must be cut at 45 degrees. So it will be one inch measured along the length of the pipe or 1.414 inches measured along the 45 degree cut. When you look at the cut face at right angles (90 degrees) you will see an ellipse that is 1 inch wide and 1.414 inches long.
