Want this question answered?
A 15 Amp extension cord can be plugged into a 20 Amp circuit. It is important that what you're extending does not require more then 10-12 Amps.
If your extension cord is truly a 30 amp cord then it is composed of #10 wire. #10 wire is rated at 30 amps. All you have to do is remove the 30 amp plug and receptacle ends from the cord and install 15 amp cord ends.
Make sure the wire size of extension cord is AWG 12 or AWG 10. Also circuit must support the 20A at main panel. Standard household extension cords are usually AWG 14 which are not sufficient to carry 20A.
Extension cords are not used at 5500 volts.
If your question is can you use a #6 flexible SOOW cord and put a 30 amp plug on it, then yes. The breaker that feeds the receptacle that the cord will plug into can be no larger than a 30 amp breaker. What limits the cord capacity to 30 amps is the ratings of the plug on the end of the cord.
A 15 Amp extension cord can be plugged into a 20 Amp circuit. It is important that what you're extending does not require more then 10-12 Amps.
If your extension cord is truly a 30 amp cord then it is composed of #10 wire. #10 wire is rated at 30 amps. All you have to do is remove the 30 amp plug and receptacle ends from the cord and install 15 amp cord ends.
Make sure the wire size of extension cord is AWG 12 or AWG 10. Also circuit must support the 20A at main panel. Standard household extension cords are usually AWG 14 which are not sufficient to carry 20A.
no, you should use same amp and volt.
A 14 gauge extension cord can safely carry 15 amps, but not very far. Number 14 gauge extension cords are only rated for about 13 amps according to the labels on the cord. This is because the insulation is not intended to withstand the heat of currents above this level. Running this cord over 50 feet or loading it to 18 amps would be unacceptable.The likelihood of the cord maintaining the 18 amps for any amount of time for the high current to do any damage to the insulation of the cord is not very great. Extension cords are only an extension of the 15 amp wall circuit that they are plugged into. On overloading the extension cord by that amount the overload will trip the 15 amp supply breaker. An example of this is jamming a circular handsaw when it is plugged into the end of a 50 foot extension cord. The next action that is taken is to reset the tripped breaker.
Extension cords are not used at 5500 volts.
yes.
If your question is can you use a #6 flexible SOOW cord and put a 30 amp plug on it, then yes. The breaker that feeds the receptacle that the cord will plug into can be no larger than a 30 amp breaker. What limits the cord capacity to 30 amps is the ratings of the plug on the end of the cord.
Yes the rated voltage is a maximum. A 250 v cord might be slightly thicker than one for 125 v. <<>> The voltage rating of an electrical extension cord is the insulation factor of the cord. These cords come in two insulation ratings, 300 volts and 600 volts. If the voltage rating is within the parameters of the cord maximums then it is safe to use it on that voltage. The amperage of the cord is based on the wire size of the cord's conductor. The rating of 10 amps will fall within the #14 cord size. Remember the longer the cord the larger the wire size should be to prevent voltage drop at the connected load end.
Use #12 wire and a 20 amp two-pole circuit breaker.
Yes, if the manufacturer installed a parallel blade 15 amp rating cap on the end of the cord then just plug it in. The circuit that you plug into should be a dedicated circuit (nothing else on the circuit) because the amperage will be 13 amps at 120 volts.
When purchasing an extension cord it is important to make sure you get one that is large enough to handle the voltage needed. There are some guide lines available through home improvement websites that can help in the buying process.