0
HP = (Current x Voltage)/746, or HP = (IE)/746 (disregarding %Efficiency)
So, you have to solve for I, current:
I = (746 x HP)/E
Wiki User
∙ 10y ago
Add your answer:
Earn +20 pts
How many amps is 75 milliamps?
There are 0.075 amps in 75 milliamps.
How much current does a 75 watt light bulb draw from a 120v wall outlet?
It's 75/120 and the answer is in amps.
How many amps load taken to 75 hp motor?
The answer is that it depends upon the a. efficiency (to determine its input power). b. supply voltage. c. nature of the supply (single-phase, three-phase, d.c., etc.)
What size of circuit breaker do you use for 25amperes induction motor?
Read the specification plate on the motor to determine the amount of current that the motor uses, as well as the voltage and phase. Most likely, it will be a 3 phase motor, so you can't simply connect it to your house wiring, but without sufficient information, it is impossible to tell you all of the specifics. <<>> The code book rates the amperage of a three phase 40 HP motor by different voltages. at 200 volts - 120 amps, 230 volts - 104 amps, 460 volts - 52 amps and 575 volts - 52 amps. A breaker for a motor has to be sized to 250% of the motors full load amps. Also the wire size for a motor has to be 125% of the motor full load amps.
How many amps does a hair dryer use with 25 volts 60 hz and 1500 watts?
Amps = Watts / (Volts x Power Factor). Now a hair dryer has a motor and a resistive heater so if we assume a PF = .8 the answer is: 1500 / 20 = 75 amps. Since it is unlikely that you have a 75 amp hair dryer you must mean 125 volts. The answer for that would be 1500 / 100 = 15 amps which is still high, but believable. If we assume a Power Factor of 1 and ignore the motor contribution to Power Factor we have 1500 / 125 = 12 amps.
How many wires for single phase 100 amp 240 volt service?
cable size for 90 amps 3 phase 440 v <<>> A #3 copper conductor with an insulation factor of 75 or 90 degrees C is rated at 100 and 105 amps respectively. If this feeder is for a motor connection the wire size has to be increased to 125% of the full load amps of the motor.
How many amps is needed to run 3200 watts?
Watts = Amps x Volts x Power Factor For a motor the Power Factor is less than 1 and might typically be about .75. For a resistive load like a toaster PF = 1. If you know the Voltage and PF and know the wattage you can calculate amps. Amps = Watts / (Volts x PF)
How many amperes will a 75 W lamp draw on a 110 V line?
.625 ampsI know you said 110v but most homes will be 120volt ...well near itwatts divided by volts equals amps
How many amps can 4 ought aluminum wire carry?
Aluminum 4/0 wire car carry 180 amps at at 75 degrees Fahrenheit or 205 amps at 90 degrees. .
How many watts does a motor need to run for 30 minutes?
75 kw motor
How many amps will a kW Generator produce?
Typically 75 amps on natural gas, 85 amps using propane. Peak amps(for less than a second) to start a big appliance, like an A/C condenser, are 130.
What is the difference in wiring a 12 3 phase motor at low voltage between run and start?
You have to wire both the run and start windings. The start windings will automatically be removed from the circuit once the motor is at 75% of normal speed. The start winding gives you more torque to start the motor.
