As many as you want. It is the power consumed by the thing(s) plugged in that is of concern.
No. Receptacle is rated at 15 amps and the wire that feeds it will also rated at 15 amps. Since it will take 20 amps to trip the breaker the wire will be become overloaded. The above is true only if it is a single dedicated outlet. You can use 15A duplex outlets on a 20A circuit, ie: kitchen and dining room outlets per the National Electrical Code.
The only safe way to change your (fuse/breaker) would be to check your wire size and your load size. Fourteen guage wire is rated for a maximum capacity of 15 amps, if your wire size if 12 guage copper then the answer to your question is yes you can change your (fuse/breaker) to a 20amp. You should also call a qualified electrician to install your (fuse/breaker)
From the 1994 Ford Econoline Owners Guide #8 radio memory, 15 amp fuse. #11 radio and clock, 15 amp fuse. #14 power windows, 20 amp circuit breaker.
Normally 15 amp max
Yes, but don't try to put 15 amps through it! You might need to change your plug too!
no
Technically, they can be on a 15 amp breaker when you use 15 amp outlets. There is a difference. Be sure to check your local code (just call the city building department and tell them you have a code question). some cities require the bedroom outlets to be on an arc-fault breaker.
Use a 15 amp breaker and 14 AWG wire and all switches and outlets rated at 15 amps or greater.
A 30 amp breaker is usually used for a dedicated 30 amp device. Ordinary 15 amp receptacles can not be connected to a breaker of higher trip capacity than the rating of the receptacle. The wire size for a 30 amp breaker is #10 AWG.
A 15 amp breaker protecting # 14 wire.
There is no limit as to the amount of circuits you can have in a garage. If you mean how many devices on a 15 amp single circuit breaker then the answer is 12. Be sure to total in light fixture outlets and switch boxes.
No more than ten. If you used a 20-A breaker it would be up to 13.
It's the amps that are controlled by the breaker not the volts. You can have a 600 volt 15 amp breaker, you can have a 347 volt 15 amp breaker. The breaker will trip when you exceed 15 AMPS.
Replace the 30 Amp Breaker with a 15 Amp breaker.
No, the six outlets are not amperage rated to be connected to a 20 amp circuit. A normal 15 amp receptacle can not be protected by a 20 amp breaker. Change the 20 amp breaker to a 15 amp breaker. This combination will pass code regulations. =============== In the United States, in a home, you can connect two hard-wired (not cord and plug connected) fans and six receptacles (outlets) to a single 20 amp circuit provided the 2 fans do not draw more than 10 amps together. If they are cord and plug connected, this limitation on the fans does not apply. In commercial and industrial installations, power to hard-wired equipment is provided on different circuits than receptacles.
Yes, you can use lower amperage outlets - the problem would come if you were trying to run a 20 amp appliance on a 15 amp circuit or plug a 20 amp appliance into a 15 amp outlet. It would be better, though, as some kitchen appliances could exceed 15 amps (toaster ovens, some coffee makers, electric griddles, etc.) could try to draw more than the 15 amps your outlets are designed for. Perhaps you could get some 20 amp outlets and use those 15's in a hallway or something less likely to have high amperage draw.
If there is any additional load on the outlets greater than 2.5 amps the breaker will trip. Loads of 1500 watts should be on a dedicated breaker. If the total load exceeds 15 amps the breaker will operate. However many of the outlets might supply only lights, TVs or nothing at all, so in those conditions it's OK.