0
Two, and possibly a ground. The ground will be clearly marked with a green colored screw.
Wiki User
∙ 13y ago
Add your answer:
Earn +20 pts
How many hot terminals are there on a 3-way light switch?
No good way to answer this. A 3-way light switch has one wire coming to it, two wires run to the second switch and one back out of the second switch to the light. At any point, any one of the terminals may be "hot". The only one always hot is the first single terminal that is the power source.
Intermediate switch layout?
The strappers from each two way switch go to the four way switch. The strappers from one switch go to terminals 1 & 2, the other two go to terminals 3 & 4.
How can you disable one switch of a two way lighting switch?
Put all three wires from the one switch under one terminal.
What type of switch would be used to control a lighting load from one control point?
In this type of situation, where there is more than one lighting circuit, a lighting contactor would be used. These types of contactors can be obtained in four and five pole configurations. Make sure that the contactor is rated for lighting loads and not motor loads. A normal switch, single pole single throw, would be used to switch the contactors on and off. A single switch could then be used to control as many contactors as you need to operate the lighting circuits.If there is just one lighting circuit, the total circuit amperage must be known, then the switch would be sized to the amperage of the circuit.
What is a one way dimmer switch?
It is the terminology given to differentiate the dimmer switch from a three way dimmer switch. It is a replacement for an ordinary lighting load switch when you want to dim the lighting load for aesthetic value.
How many hot terminals are there on a 3-way light switch?
No good way to answer this. A 3-way light switch has one wire coming to it, two wires run to the second switch and one back out of the second switch to the light. At any point, any one of the terminals may be "hot". The only one always hot is the first single terminal that is the power source.
Intermediate switch layout?
The strappers from each two way switch go to the four way switch. The strappers from one switch go to terminals 1 & 2, the other two go to terminals 3 & 4.
How can you disable one switch of a two way lighting switch?
Put all three wires from the one switch under one terminal.
What type of switch would be used to control a lighting load from one control point?
In this type of situation, where there is more than one lighting circuit, a lighting contactor would be used. These types of contactors can be obtained in four and five pole configurations. Make sure that the contactor is rated for lighting loads and not motor loads. A normal switch, single pole single throw, would be used to switch the contactors on and off. A single switch could then be used to control as many contactors as you need to operate the lighting circuits.If there is just one lighting circuit, the total circuit amperage must be known, then the switch would be sized to the amperage of the circuit.
What is a one way dimmer switch?
It is the terminology given to differentiate the dimmer switch from a three way dimmer switch. It is a replacement for an ordinary lighting load switch when you want to dim the lighting load for aesthetic value.
How do you hook up two ways switch to three ways?
Your 2 switches will have 3 terminals each. One will be copper colored and two black. You will require a 12-3 WG wire between the switches. The Travelers: The black terminals will be connected together one from switch a to switch b and the other from switch a to switch b, it does not matter which black terms you choose to go from switch a to b The brass terminals one will go to the light switch a and the other to a power source switch b.
What is the wiring diagram for a light switch in Australia or New Zealand?
In Australia we use 1.5mm2 TPS cable for lighting circuits. The colours for fixed wiring are red - active, black- neutral and green/yellow for earth, also white is used for switch wires. All luminaires and lighting points must have an earth at their location. The process for a simple lighting circuit for looping at the switch method (feed starts at the switch) - one switch and one light point is:The feed (active) goes to the common point on the rocker switch and the neutral goes to the loop terminal on the rocker switch. The earth is connected to a two screw connector separate from the switch. A switch wire is then connected from terminal 1 of the rocker switch to one of the main terminals (these are the terminals across which the lamp terminals are connected) on the batten holder ( this is the fitting which holds the lamp). The other main terminal on the batten holder is connected to the loop terminal on the rocker switch with the neutral. The earth conductor is connected from the two screw terminal at the switch position to the earth terminal in the batten holder.As always, if you are in doubt about what to do, the best advice anyone should give you is to call a licensed electrician to advise what work is needed.Before you do any work yourself,on electrical circuits, equipment or appliances,always use a test meter to ensure the circuit is, in fact, de-energized.IF YOU ARE NOT ALREADY SURE YOU CAN DO THIS JOBSAFELY AND COMPETENTLYREFER THIS WORK TO QUALIFIED PROFESSIONALS.
How do you connect 2 black and 2 red wires to a new switch?
switches work by interupting the hot side of a wire loop, so what you do is you wire your non hot (usually black) wires directly to the device you are trying to control, next, to one side of the switch you connect your two reds, then to the other side of the switch connet the hot lead from your device.
What is the wiring diagram for a light in Australia or New Zealand?
In Australia we use 1.5mm2 TPS cable for lighting circuits. The colours for fixed wiring are red - active, black- neutral and green/yellow for earth, also white is used for switch wires. All luminaires and lighting points must have an earth at their location. The process for a simple lighting circuit for looping at the switch method (feed starts at the switch) - one switch and one light point is:The feed (active) goes to the common point on the rocker switch and the neutral goes to the loop terminal on the rocker switch. The earth is connected to a two screw connector separate from the switch. A switch wire is then connected from terminal 1 of the rocker switch to one of the main terminals (these are the terminals across which the lamp terminals are connected) on the batten holder ( this is the fitting which holds the lamp). The other main terminal on the batten holder is connected to the loop terminal on the rocker switch with the neutral. The earth conductor is connected from the two screw terminal at the switch position to the earth terminal in the batten holder.As always, if you are in doubt about what to do, the best advice anyone should give you is to call a licensed electrician to advise what work is needed.Before you do any work yourself,on electrical circuits, equipment or appliances,always use a test meter to ensure the circuit is, in fact, de-energized.IF YOU ARE NOT ALREADY SURE YOU CAN DO THIS JOBSAFELY AND COMPETENTLYREFER THIS WORK TO QUALIFIED PROFESSIONALS.
Where can one purchase Hanover lighting?
There are many places where one can purchase Hanover lighting. One can purchase this lighting from many different retailers such as Lowe's that specialize in lighting products.
How do you wire a light switch that has two gold and one copper coloured screw?
Unfortunately there are no electrical regulations that define whether copper or brass screws should be used for any particular wires. It is important to understand what type of switch it is. The material used for the screws provides no useful information.
How many terminals does a voltage source have?
One
