0
What else can I help you with?
How many volts can a strip of take before it melts?
It's always an interaction of volts and amperes, so even if you would have posted a complete question (a strip of what?) it wouldn't have been possible to answer.
How many amps can handle in 12 volts a 600 volts 15 amps rated terminal bar?
The terminal strip's rating is 15 amps at 600 volts. It does not matter what the voltage is up to 600 volts, the maximum amperage allowed on the strip is 15 amps. It could be 15 amps at 12 volts or 15 amps at 600 volts or any voltage in between.
Can you make a 9 volt battery out of lemons?
Yes- you need 6 lemons, 6 strips of copper metal and 6 of zinc metal. insert one of each strip into a lemon, and connect zinc to copper on next lemon, repeating until all 6 are connected. Each lemon produces about 1.5 volts- so 6 lemons is about 9 volts.
What is the power voltage electrical strip heaters supplied with?
Usually with 240 volts. Some under 1000 watts will use 120 volts.
What was the affected part of an Emacs plugged to a 220 volts operating at 110 volts?
just the metal parts
What is the common voltage to heat strip?
The common voltage for heating strips, often used in electric heating applications, typically ranges from 120 volts to 240 volts. In residential settings, 120 volts is commonly used for smaller heating strips, while 240 volts is more common for larger units or applications requiring higher heat output. Always check the manufacturer's specifications for the specific heating strip being used.
How deep do you bury 120v wire?
Minimum coverage for non vehicular areas; for conductors or cable not having a metal sheath or armour, under 750 volts, the required depth is 600 mm. For conductors or cable having a metal sheath or armour, under 750 volts, the required depth is 450 mm. Minimum coverage for vehicular areas; for conductors or cable not having a metal sheath or armour, under 750 volts, the required depth is 900 mm. For conductors or cable having a metal sheath or armour, under 750 volts, the required depth is 600 mm.
How many amps does a 250 watt metal halide bulb draw?
To determine the amperage drawn by a 250-watt metal halide bulb, you can use the formula: Amps = Watts / Volts. Assuming the bulb operates on a standard voltage of 120 volts, it would draw approximately 2.08 amps (250 watts / 120 volts). If it operates at 240 volts, it would draw about 1.04 amps (250 watts / 240 volts). Always check the specific voltage rating for accurate calculations.
How much voltage will an alternator have to have before it will give 13 volts or more?
I'm not sure I understand your question. An alternator will have to produce 13 volts to charge a battery at 13 volts. Most alternators are able to produce 14+ volts but the range is 13.5 to about 15.5 volts.
How much volts does a triple A battery have?
A standard AAA battery typically has a voltage of 1.5 volts. This applies to alkaline and zinc-carbon AAA batteries. Nickel-metal hydride (NiMH) rechargeable AAA batteries usually provide about 1.2 volts.
Can you run one 1500 watt heater on a 125V- 15A 60Hz power strip?
Yes, a 1500 watt heater operating on 120 volts has an amperage of A = W/V. Amps = Watts/Volts = 1500/120 = 12.5 amps. It is not a recommended practice to do so.
How can I tell if a fuse is blown in my car?
pull out the fuse and in the middle of the plasitc body you will see a metal strip if this is smoked an canot be seen or the plastic has lost color in anyway it is blown you could also apply a volt meter to both side of the fuse an turn it to dc an if it does not get any volts it is blown but just looking is way easyer
