0
my 94 xr100 was blown up an had only 35 psi shes toast lol
Wiki User
∙ 9y ago
Add your answer:
Earn +20 pts
How much oil does a 1987 Honda xr100r hold?
one quart of four stroke motorcycle oil. I use 10w 40. do not use car or truck oil!
How do you replace the ignition lock cylinder on a 2004 Honda civic?
The ignition lock switch is found under the steering column on a 2004 Honda Civic. Remove the steering column and ignition switch. Loosen the mounting screws that hold the cylinder in place. Pull and replace the lock cylinder.
What is effect of a bend valve stem on engine performance?
The bent valve won't be able to seat properly to create a seal, so the cylinder won't hold compression. The end result, a dead cylinder.
How do you do a compression test on a car engine?
Remove all spark plugs.Insert compression gauge in cylinder #1Hold throttle open and crank for 5 seconds.Record reading.Repeat on all cylinders.Remove all spark plugs.Insert compression gauge in cylinder #1Hold throttle open and crank for 5 seconds.Record reading.Repeat on all cylinders.
What does compression ratio mean in car motors?
In an internal combustion engine, there are cylinders that have pistons in them. When the piston is down you have an open cylinder that has a specific size of volume that it will hold. When the piston moves back up to as high as it can, it compresses all that space into the new space and that is the compression ratio.
Auto Technician A says the total volume of all the cylinders in an engine is called the compression ratio?
The volume of an engine is called displacement and is typically measured in cubic inches or liters. An eight cylinder engine that could hold 1/2 liter of water (or air) in each cylinder would be a four liter engine. As the pistons move to the top of the cylinder in an exhaust stroke, they theoretically "displace" the 1/2 liter of air in each of the cylinders. The compression ratio is calculated during the compression stroke. If the piston occupies 90% of the enclosed cylinder space when it is at top dead center, the compression ratio is said to be 10 to 1, or 10:1. If the displacement of the cylinder was 10 cubic inches, it would have been compressed to 1 cubic inch.
How do you run a compression test for 2001 Saturn SL?
Running a compression test is pretty much the same for all internal combustion engines.Remove all sparkplugs, marking where the wires went; you don't want to connect the wrong wires to the plugs when you're finished.Start with cylinder 1, screw in a compression gauge where the sparkplug just came out. Some compression gauges just press in, but I prefer the screw in type.Have an assistant engage the starter as though trying to start the engine. Obviously the engine won't start without plugs.You should hear and/or feel the engine compression on the single cylinder with the gauge in place; make sure that cylinder goes through compression cycle at least 3 times.Read the value on the gauge. The gauge should hold the compression reading, allowing you to record the reading.Write down the compression reading and the cylinder number.CLEAR THE COMPRESSION GAUGE. You can release the compression reading, usually by pressing a button or turning a knob. It's different for different style gauges.Repeat the process for all cylinders.Compare the compression value for all cylinders; they should be within a few percent of each other. Any small variance can be attributed to cylinder or valve wear. Large differences indicate severe problems. If any two adjacent cylinders have zero compression, you probably have a blown head gasket.
How many gallons of gas does a 1996 Honda Civic LX hold?
The 1996 Honda Civic with 1.6L 4-cylinder engine has rated fuel capacity of 11.9-gallons. The recommended gasoline type for the vehicle is regular unleaded.
How does a arch bridge use compression?
An arch bridge uses compression to hold itself together
How big a cylinder will one milli on gallon hold?
How big a cylinder will one million gallons hold
How much oil does a honda accord lx hold?
Almost all Honda's V6 or 4 cylinder hold 4.5 quarts. Change the oil/filter, add 4 quarts, start the engine, shut down, wait 30 minutes and check the oil level. Add as necessary to reach the full mark.
How do you change the driver's door lock cylinder on an 1987 Honda Accord?
The lock cylinder is held in by the chrome on the outside in the cylinder where the key goes in to turn it. from the inside if the door - the outer piece of the chrome (the ring) has a couple of 'fingers' that help hold it on - push it off from the inside so you can reuse it. you should be able to push the cylinder out from the door now.
