0
Add your answer:
Earn +20 pts
How much a 12 inch by12 inch concrete block weigh?
Where are 12 inch concrete blocks applied?
In a room 12 feet long by 12 feet wide how much 16 inch square tiles you would need to cover the floor?
81 but it also depends on your grout line size. I based this on no grout line. too many good, not enough bad
How much does 115 inch equal in foot lbs?
An inch is a unit of length. A foot pound is a unit of pressure. The two units are therefore incompatible.
How much more batter is in a 10 inch round cake pan than an 8 inch round cake pan?
It depends on how deep the cake pan is.
How much sand is needed to cover 230 square feet 1 inch deep?
230
How much water should you have to drain out of your return line?
i have to drain out 4800 cusec of water
How much water drains out of a 4 drain?
you need to know the PITCH of the drain line to give an proper answer
You are working with a 3 inch PVC drain pipe and a 3 inch PVC flange and there is too much play as you insert the flange into the drain pipe?
Probably the wrong size flange. Is the flange a toilet collar? If so the pipe is probably 4 inch.
How much fall in a toilet drain pipe?
From various sources I gathered that the minimum fall (slope) is 1cm fall over 1m distance. Converted that is 0.125 (1 eighth) inch fall over 1 foot distance.The maximum that should not be exceeded is 1cm fall over 20cm distance. Converted that is 0.25 (1 quarter) inch fall over 4 foot distance.
Can you tie a 1.5 inch sink drain and a 2 inch shower drain together into a 2 inch connection at a 4 inch main line?
Answering this question leaves a lot of unknowns; 1) Is this in the basement, in the floor, under concrete, or, going to be. 2) Is this on a main level, above a basement (Not a crawl space!). And 10 more questions! There is some planning, but, could be trying to answer 25 different scenario's, as much supplied info. will help. For a short answer to keep it simple, the answer is, yes, you can!
How much slope do you need for a drain pipe from a new bathroom and what do you do if there isn't enough slope?
One quarter inch per foot is standard "slope". This equates to a quarter bubble on a level. If you don't have at least one eighth of an inch "slope", your drain will not work properly and will clog constantly.
How much oil is in tank if you have 9?
There are plenty of inch to gallon conversion charts on line. Just google it
If all the water in the atmosphere were to precipitate how much rain would fall?
There would only be about an inch of water in a given area.
Where is the fuel tank drain plug in a 96 ford escort wagon?
No drain plug. Use as much gas as you can then make sure you have a pan near by and do not smoke while disconneting the fuel line.
How do you change oil cooler lines on a 1994 Chevy Suburban?
Things You'll Need Jack Jack stands Drain pan 3/8-inch ratchet and socket set Line wrench set Teflon tape Replacement oil cooler line fittings Replacement oil cooler lines Replacement oil cooler line plastic inserts Oil Lift up the vehicle using the jack and place it on jack stands. Make sure the vehicle is secure before you crawl underneath it. Drain the oil from the oil pan into the drain pan by unbolting the drain pan bolt using the 3/8-inch ratchet and socket. Once the oil has drained out, reinstall the plug. Unscrew an oil cooler line from the radiator using the line wrench. This will spill out some oil, so you may want to keep the drain pan handy. Follow the oil line to the oil filter, and unbolt the bracket that holds the oil lines to the engine using the 3/8-inch ratchet and socket. Then push in the plastic clip on the oil filter assembly to release the line. Unscrew the fitting from the oil cooler housing using the 3/8-inch ratchet and socket. Then wrap Teflon tape around the end of the replacement fitting and install it in the oil filter housing using the 3/8-inch ratchet and socket. Don't tighten it too much, otherwise you risk cracking the housing. Insert the replacement plastic fitting into the fitting manually. Run the replacement oil cooler line from the radiator to the oil filter housing and push it into the plastic clip on one end, and tighten it down using the line wrench on the other. Repeat Steps 3-5 for the other oil cooler line. Once it's replaced, tighten down the bracket that secures both lines to the engine using the 3/8-inch ratchet and socket. Fill the engine with the amount of oil the manufacturer recommends.
How much ice will bring down power lines in an ice storm?
It takes as little as a quarter inch of ice to bring down a power line. Just one quarter of an inch can add 500 pounds of weight to the power line.
Why does Lady Gaga fall down so much?
well when your singing and dancing in high hells all the time... wouldn't you fall down too? she wears 12 inch heels that's why.
