0
4 pints many or 2 qts for many. You just fill to bottom of fill hole when cover replaced. The tricky part is getting a good seal on the cover.
Wiki User
∙ 13y ago
Add your answer:
Earn +20 pts
How do you change a cv axle for your 1990 integra?
loosen axle bolt take outer tie rod bolt off remove from hub take bottom ball joint bolt off seprate from hub and pull out alittle and axle can come out then put it back together
What kind of gear oil does my truck take in the rear axle?
purple
Where can you find out the gear ratio on a 10 bolt rear end from a 1971 Chevelle Malibu?
While the axle code is stamped on the passenger side axle tube, the most reliable way is to take off the back cover and count the teeth on the pinion and ring gear and divide the numbers because there is NO guarantee the gears are original.
How do you take the axle out of a Chrysler 8.25?
To remove the axle shaft, first remove the wheel, and brake drum/rotor. Second, remove the differental cover. Third, remove the bolt holding the spider gear shaft, and remove that shaft. Fourth push inward on the axle shaft to remove the horseshoe clip on the inside. The axle shaft will now pull out.
Do you put gear oil or transmission fluid in a 1992 Nissan Sentra trans-axle and where does it go?
BUY A BOOK OR CALL THE DEALER AND ASK THEM you need to take the speedomiter cable out of the transmission remove one 10mm bolt i belive and there will be a gear on it and it will say add or low on it its simple
Removing rear axle from 1988 ford ranger?
Take rear cover off and losen the 6mm. head bolt. Rotate the gears and remove c-clip from axle. Slide axle out.
Where is the bolt located to fill the rear axle for a 96 ford bronco?
plug is on the left front of axle housing. take a 3/8 drive to remove
How do i change the axle boot of a bug?
If it's a swingaxle Bug, they make a kit with a retrofit boot. You cut the old boot off and bolt the new one together around the axle. An IRS Bug requires a pair of circlip pliers and a CV bolt socket. Take the axle out of the car and remove the circlips from the axle. Knock the axle out of the CVs with a big hammer and a drift punch. Throw the old boots away. Clean and repack the CVs, put the boots on the axle, then the CVs on the axle, then the axle back in the car.
How do you determine the front differential gear ratio?
It will be the same as the rear axle. Or take the VIN to the dealer, it is coded into the VIN number.
What is the oil capacity of the rear differential on a 2002 suburban?
It will take just under (3) quarts/liters of 75/90 gear oil. I highly recommend using full synthetic gear oil (mobil 1). Also, you do not have to take the rear axle cover off , as ther is a drain bolt that is flush on the bottom of the axle The answer below is also correct I don't know the capacity, but I know how to tell if it is full. Normally you add gear lube until it runs out the hole used to fill it. As soon as some starts to come out stop adding lube and insert the plug.
Replace rear axle on 2000 Dodge Dakota?
First off do you want to change an axle shaft or the complete axle housing? for the axle shaft,jack the rear of the truck up take off the wheels and brake drums.make sure truck is securly supported with jackstands.remove the differental cover locate the bolt that holds the cross pin in the carrier.remove the bolt,slide out the cross pin.push the axle in towards the center and remove the c-clip holding the axle in.remove the axle shaft carefully so not to damage the bearings or seal.
How do you change rear shock absorbers on a Kia Rio?
jack up rear of car and place axle stands under rear chassis rails then lower car onto axle stands, place jack under rear axle and jack up to take up slack on rear axle and shock absorbers, undo top two bolts and lower axle down then undo single bolt at axle end. bolt new shocker into place at axle then jack up axle till top two bolt holes are lined up then install bolts at top end. remove jack and repeat on other side.
