0
Want this question answered?
Be notified when an answer is posted
Add your answer:
Earn +20 pts
What happens to the coil of wire when someone presses the switch?
If the coil is connected to a circuit and the switch is closed then, provided there is a power source, the coil will become energized.
What is a tap on a Tesla Coil and where should you wire it?
If you are working with a coil, you should have all parts of the coil and knowledge to work with them. In the related links box below, I posted a websited which has all this knowledge and another one about builduing the tesla coil.
Why when I drive then dies at stop light losing power?
because the car isn't used to stopping that long your ignition coil is going bad my was doing the same thing losing power at a stop light or stop sign after about 30 minutes changed coil packs now its fine unless your engine is low of water and runing hot the coils should fix it.
What do you do when no current is coming to the coil?
Turn the power supply on. Then check all connections.
Why current lagging in the coil?
The coil consists of inductance. Due to inductance the current lags the voltage. So, the power factor is lagging.
Cylinder coil on Mitsubishi eclipse keeps going bad why?
it might be next to something hot. or there is to much power going to that coil. it might be next to something hot. or there is to much power going to that coil.
What reading should a typical ignition coil be?
The primary ignition coils should have at least 10 amps of power running through it. Generally, this is far less power than what flows through the secondary ignition coil.
1990 Mitsubishi Valant Power transferrs to the coil but coil is not transferring power If the coil is getting power why is there no spark?
The coil is bad or the ignitions system is grounding out somewhere.
How does a power mat for an Android device work?
The primary coil is in the power mat while the secondary coil is in the Android device. Power goes from the primary coil to the secondary coil, which allows the phone to charge.
What happens if you use a 12 volt coil with a 6 volt system?
Probably not much because 6 Volts is not enough to power a 12 Volt coil
1991 Dodge Dakota that won't START - I have already replaced the pick-up in the distributor and coil and coil wire you have power to the coil but there is not power coming out of the coil - help?
Replace the ECU.
Why you have no power going to your distribuitor in your 1974 stingrayand when it does burns your coils please help?
There should be no power directly to the distributor. Power goes to one side of the coil. The distributor pulls voltage from the other side of the coil down to ground and every time the coil is supposed to fire, the connection to ground is opened. When starting, voltage goes directly to the coil. When the engine is running, the voltage goes through a resistor.
What happens when there is a load fluctuation in a marine auxiliary diesel engine?
Your voltage regulator should compensate for it by changing the frequency to the field coil of the generator and producing more power. The voltage regulator should compensate for it by increasing the frequency to the field coil of the generator, thus producing more power.
How does a motor generate spark to the spark plugs?
Answer One of three ways ,magneto , coil, high energy ignition.magneto use's magnets to energize the coil, coil use's the battery's power run through the coil then the points open and the spark is released. H.E.I. use's battery power in much the same way as the coil but the coil is internal and the points are electronic. CheckSpark can safely and quickly check all three type,s.
84 buick skylark turns over but wont start there was no spark to plug wires or to distrubutor cap or to coil I replaced coil still no luck?
you should also replace condensor. but if you have no power to coil, u will not have power to anywhere else check for broken wire or bad connections also check fuses
What causes no power to coil pack in 98 dodge stratus?
What causes no power to coil pack in 1998 dodge stratus ?
How to calculate power consumption by induction melting furnace?
simply by measuring the coil voltage, coil current & power factor.
