0
How much torque for valve cover bolts on a 1993 ford tempo gl 2.3 liter engine?
Wiki User
∙ 12y ago
about 7-10 ft/lbs, do a star pattern its not super sensitive, but i would gently snug all bolts and tighten a bolt on one side then one on the other until all were tight.
Wiki User
∙ 12y ago
Add your answer:
Earn +20 pts
What is the valve cover torque on a 2000 Mazda Protege 1.8L?
The 2000 Mazda 1.8 liter engine valve cover torque specification is 45 pounds. The valve cover bolts should be torqued in 15 pound intervals.
What are the valve cover torque specs for a 2001 3.0 Mitsubishi Montero Sport?
The 2001 Mitsubishi Montero Sport 3.0 liter engine valve cover torque specification is 40 pounds. You do not want to over torque the valve cover bolts, as you may ruin the valve cover gasket.
What are the torque specs for a 1996 Chevy s10 4.3 liter?
For the 1996 Chevy S-10 4.3 liter, the torque specs for the crankshaft damper bolts is 70 ft. lbs. For the cylinder head bolts, the torque is 65 ft. lbs, and for the engine mount-to-head bolts, the torque is 35 ft. lbs. For the engine mount-to-frame bolts, the torque is 52 ft. lbs.
What are the Torque specs for intake and plenum tubes bolts on corvette 5.7 liter TPI engine?
== ==
What is the torque specifications for the head bolts on a 2.2 liter 4 cylinder out of a caviler?
The Chevrolet 2.2 liter engine had bolt torque specification is 120 pounds. The head bolts should be torqued in 40 pound intervals.
What is torque on the head bolts 2002 Cavalier 2.2?
The 2002 Cavalier 2.2 liter engine cylinder head bolt torque specification is 120 pounds. The cylinder head bolts should be torqued in 40 pound intervals.
What is the head bolt torque on a 2002 gm 2.2 liter 4 cylinder engine?
according to chilton repair manual. long bolts- 46 lbs short bolts- 43 lbs then after torqued, tighten an additional 90 degrees. the long bolts are the bolts under the valve cover. the short bolts run along the exhaust side of head
What is the torque setting for the Exhuast manifold on a 5.9 liter Cummins 24 valve diesel engine?
manifold to head bolts 32 ftlbs
Whats the torque specs for a 4.3 vortec intake manifold?
The torque specifications, for a 4.3 liter engine manifold, is 45 pounds per square inch. Torque the manifold bolts in 15 pound intervals.
How do you change torque converter on 97 dodge ram 1500 5.9 liter?
Remove the lower cover plate on the transmission to engine to gain access to the bolts and remove them. You will have to rotate the flywheel to get to all of them. Remove the driveshaft and drop the transmission.
What is Bolt torque sequence for valve covers on 5.4 Triton ford f-150 pick-up- truck?
The valve cover torque specifications, for your 5.4 liter Ford engine, is 15 pounds per square inch. The bolts should be torqued five pounds at a time.
What is the torque specification on a water pump for a 1998 buick skylark wth a 3.1 liter engine?
According to the chilton manual the 5 water pump bolts torque to 89 inch pounds. The four bolts that hold the water pump pulley torque to 18 foot pounds.
