0
Want this question answered?
Be notified when an answer is posted
Add your answer:
Earn +20 pts
How the voltage is induced in a single phase transformer?
The changing magnetic flux in the iron core of the transformer induces a voltage in the windings.
How the losses will reduce if you keep the flux density in high level in power transformer?
The flux density is set at the most the core material can stand, which for standard laminated transformer iron is around 1 Weber per square metre. Based on that and the cross-section area of the core, the volts per turn figure is calculated for both the primary and the secondary winding. If the operating voltage stays constant, so will the flux density and the iron losses.
Do magnetic flux in induction motor remains constant?
ni it doesn't
How do you improve the flux linkage between the primary and secondary windings in a transformer?
by using an iron core
How dc supply is given to transformer used in push pull amplifiers?
The dc is supplied via a centre-tap on the transformer. This ensures zero dc net flux in the transformer core, which enables a much smaller core to be used.
With aid of diagram explain why magnetic flux of transformer remains almost constant from no-load to full load?
since the volt amphere turns in secondary neautralises the primary voltamphere turns making the magnetic flux in the core remain constant
In transformer core flux depends on voltage whereas leakage flux depends on current?
In a Transformer, Core flux is the difference of primary flux and Secondary flux which are opposite to each other in direction. There difference is equal to the no load flux at all loads. So, some of primary flux passes through the core and remaining becomes leakage flux (Because Secondary flux forces it to get out of the core). Same is the case with Secondary flux. Now, flux is directly proportional to Voltage and Current. When Current increases due to increased load (and voltage remains same): Then both primary and secondary flux increase. Because both of them increase, so there difference remains same. And all remaining flux is forced out. Hence leakage flux increases with current, but Core flux remains constant. When Primary Voltage is increased: Then only primary flux increases. So difference of this new increased primary flux and previous same secondary flux increases. Hence Core flux increases with voltage, But leakage flux does not. That's how In transformer core flux depends on voltage whereas leakage flux depends on current.
Is mutual flux in transformer constant for all loads?
The flux is set by the voltage applied to the transformer. In most applications, the voltage is constant, and therefore the flux is constant also.
Why a double coil transformer does not work on a pure DC voltage source?
According to Faraday's Law only if there is change in flux linkage of a conductor then current is induced between mutual inductors. Now DC will induce a constant a constant flux in the transformer core, consequently in the secondary coil. So constant flux cannot induce a current in the secondary. SUBHRA JYOTI SAHA
Why transformer is called constant flux machine?
when a load is connected to a transformer current(say I2) flows through secondary coil thus an M.M.F (N2I2) is produced ,this produces the secondary flux. This flux reduces the the main flux induced in the primary & also reduces E.M.F E1 in the primary As a result more current is drawn from the supply. This additional current drawn is due to the load component(say I2' ) This I2' is anti-phase with I2.This I2' sets a flux which opposes the secondary flux & helps the main flux. The load component flux neutralises the secondary flux produced by I2 .The M.M.F N1I2' balances N2I2.Thus the net flux is always at constant level. As practically flux is constant,the core loss is constant for all loads. Hence a transformer is always called a Constant Flux Machine.
Why is a transformer called constant flux machine?
when a load is connected to a transformer current(say I2) flows through secondary coil thus an M.M.F (N2I2) is produced ,this produces the secondary flux.This flux reduces the the main flux induced in the primary & also reduces E.M.F E1 in the primaryAs a result more current is drawn from the supply. This additional current drawn is due to the load component(say I2' )This I2' is anti-phase with I2.This I2' sets a flux which opposes the secondary flux & helps the main flux.The load component flux neutralises the secondary flux produced by I2 .The M.M.F N1I2' balances N2I2.Thus the net flux is always at constant level.As practically flux is constant,the core loss is constant for all loads.Hence a transformer is always called a Constant Flux Machine.
What is the function of the core?
the function of core is to provide path to magnetic flux,a core may be armature core or may be transformer core
What is the purpose of transformer core?
yes core is usefull in transformer since it it increase the permeability for the flux (i..e,it offers less relucyance path thanj air ).Their by decresing the losses in the transformer.
Why in transformer core is necessary?
A transformer core is a low-reluctance magnetic circuit, which ensures that most of the magnetic flux generated by the primary winding links with the secondary winding. Without a core, little of the magnetic flux generated by the primary winding will link with the secondary winding.
How the voltage is induced in a single phase transformer?
The changing magnetic flux in the iron core of the transformer induces a voltage in the windings.
The leakage flux of transformer depends on?
Actually it depends on the air gap between the core and the windings of the transformer. This is the reason why stepped core is used in medium and large transformers as it decreases the air gap between the windings and the core of the transformer.
How the losses will reduce if you keep the flux density in high level in power transformer?
The flux density is set at the most the core material can stand, which for standard laminated transformer iron is around 1 Weber per square metre. Based on that and the cross-section area of the core, the volts per turn figure is calculated for both the primary and the secondary winding. If the operating voltage stays constant, so will the flux density and the iron losses.
