0
Most just fit together tightly and will come apart with a little pulling and wiggling. Their could be paint of corrosion sticking them together in which case you may have to use a penetrating oil/solvent on the seam and hope for the best. Its possible that if its very very old, it was soldered in place - in which case it will have to be heated with a torch at the seam (better left to a professional). Worst case, saw it apart and repair with a coupler.
Wiki User
∙ 14y ago
Add your answer:
Earn +20 pts
How do you replace a multifunction switch on a 1993 Lincoln mark viii?
You have to remove the top and side covers on the steering wheel column, remove I think 4 screws-bolts, disconnect the wire connection, and remove the old switch.
Explain step by step how to put in the blower resitor?
Remove the electrical connector from the old resistor. Remove the screws holding the resistor in place. Remove the old resistor. Put in the new one and screw in the screws. Attach the electrical connector.
How do you remove a CD player from a 2002 Mitsubishi Lancer?
First you remove the knobs for the Temperature, Fan, and vent control, and u will see 2 screws, remove those. After removing, gently pry off the dash panel, exposing the bracket for the CD player. Remove the 4 screws (2 on left and 2 on right) and gently slide out CD player. Before pulling out all the way, disconnect the harness and the antenna cable. To put in another CD player, use the same brackets, just remove it from the old CD player.
How do you replace the radiator on 2004 Impala LS v6?
you have to remove the old one first. paying careful attention to where the screws/bolts come from. remove all of those, take them out carefully, then replace the radiator and connect with the bolts/screws you removed from the old one.
How do you change heater core in 01 impala?
Remove the center console remove the floor vent remove the heater core cover the heater core is right under the climate control unit remove the two screws that hold the heater core in place, open the hood and remove the heater hose from the heater core lines, now go inside and pull out the old heater core you don't have to remove the whole dash just the front of it
How do you install a Mitsubishi eclipse driver mirror?
To install the Mitsubishi Eclipse driver mirror, you will need to remove the interior door panel on the driver's side. Then, remove the cover for the mirror screws. Remove the screws and wiring and remove the old mirror. Replace the wiring and screws as you add the new mirror to the car. Then place the cover and the door panel back on the vehicle.
How do you change headlight Ford Falcon?
many old cars are very similar, you need to remove the bezel screws first then loosen the three slotted screws on the retaining ring. turn the retaining ring a little to the end of the screw slot so you can remove it. Unplug the three prong plug and remove the light. ( if the retaining ring is old you may have to remove it if it will not turn)
How do you change a fog light bulb on a 98 neon?
First you have to take out the blinker/parking light to get to the fog light, each fog light has 4 screws around it (don't touch the one on the side that's gold) undue the 4 screws and pop it out, then you have the bulb exposed and you can replace it.
How do you change the inside handle and lock on a Chevy Suburban?
depending on model the 94-98-99 old body you have to release late assembly on the side and the remove panel to then remove both screws that hold it to the door and pull out. on the 00 up you can just remove panel and remove screws that hold it to the door.
How do you change a the sidelight bulb on an Audi TT?
To change a side light bulb on an Audi TT, remove the light lens by unscrewing the screws holding it on. Then, remove the old bulb and insert a new one. Replace the cover and tighten the screws.
How to replace spark plugs on Grand Vitara 2000?
Disconnect the battery, remove the spark plug covers and cable, and remove the old spark plugs. Put in the new spark plugs, replace the covers and cable, and reconnect the battery.
How do i replace spark plugs on 1998 Isuzu Rodeo?
Disconnect the battery, remove the spark plug cable and covers, and remove the old spark plugs. Put in the new plugs, put back the covers and cables, and reconnect the battery.
