0
The 1992 Chrysler came with a couple of different radio systems -- the standard radio with cassette, the standard radio with cassette and graphic equalizer, the Infiniti I premium radio (with just cassette player), and the Infinity II premium radio (with both cassette player and graphic equalizer). The following instructions should enable you to set the time on any of these systems: To start the procedure, the radio display must be showing the time. If the radio frequency is being displayed, press the SEL button to activate the time display. 1. Press the SET button and "P" will be displayed. 2. Press the SEL button or Time Program control (on units with a graphic equalizer) and the hour will be displayed. 3. Rotate the tuning knob or push the tuning button up or down to change the hour setting. 4. Press the SEL button or Time Program control again to display minutes. 5. Rotate the tuning knob or push the tuning button up or down to change the minutes setting. 6. Press the SEL button or Time Program control one last time to complete the procedure.
Wiki User
∙ 15y ago
Wiki User
∙ 18y agoRead your owner's manual. This information can be found there.
Add your answer:
Earn +20 pts
How do you change the spark plug wires on a 1995 Chrysler LeBaron?
You remove them one at a time, and install the new one the same way.
How much is a 1992 Chrysler Lebaron convertible top?
On eBay there about $160 to $200 dependiing on if you need the rear window. You'll have to remove back seats to get at the complete convertible frame. The tops will come with instructions. Its a lot of work and very time consuming plan for a whole weekend.
How to check Brake fluid in Chrysler lebaron?
look at the fluid reseviour.. if the fluid is low.. tis time to replace the brake pads.. as the pads wear out the fluid level drops
How do you set the clock in a 1988 Chrysler Lebaron?
To set the clock on a 1988 Chrysler Lebaron you start by pressing the "set" button while the radio is on and push the volume knob in. Once you see the hour number flashing on the screen, adjust by using "seek" and press the volume knob in once you set the hour and then it will go to minutes. Adjust the minutes using the same "seek" button and press the volume knob in and the time will be set.
94 Chrysler lebaron set timing and replaced water pump and now it wont start why?
did you make sure the #1 piston was top dead center and that when you set your timing that the springs where without tension? if not its out of time
What is the date and time of nathalia ramos's birthday?
I don't know the time, but she was born on July 3, 1992.
Why clock on a 1993 Chrysler Lebaron will only keep time when in the off position When turned on the display either goes blank or displays incomprehensible dashes so neither the clock or radio work?
you have a short inside your radio.
What does a code 12 mean from a computer key search on a 1995 Chrysler Lebaron GTC convertable?
Just found the answer to my own question. Code 12 means the battery has recently been disconnected and over time the code will disappear.
Who made a 2000 Jeep?
Jeep is part of Chrysler, which was part of Diamler Chrysler at that time.Jeep is part of Chrysler, which was part of Diamler Chrysler at that time.
How do you change the headlights on a 1993 Chrysler lebaron convertible?
1993 Chrysler Lebaron Convertable bulb replacement: Purchase the correct replacement bulb(s) first, before disassembling the vehicle. See sources and related links below for replacement bulb information. Then consult your owner's manual for the replacement procedure. The owner's manual is the best place to start for bulb replacement. You may want to consider replacing both left and right at the same time in order to keep brightness and color equal (optional).
What time was Nicholas Jerry Jonas Born Time not Date?
Nick was born at 3:39am on September 16 1992 in Dallas.
How do you replace the alternator on a 1992 Chrysler LeBaron?
Same principle for all models.. top rear of engine on left hand side 1. Disconnect neg terminal on the battery 2. undo wires to back of alternator. 3. Undo pivot bolts and adjuster, loosen and slip off drive belt and remove. Remember to take old unit when you go to get new alternator. Total time.. 20 mins
