What causes a clanking noise under the motor of a 91 Saab in low gear?
The transmission on a SAAB 900 is mounted directly on the bottom of the engine. That clanking is likely coming from a broken tooth on a gear. ...
Asked in Power Steering, Toyota Sienna
Where is the steering knuckle on a Toyota Sienna 2000?
Inside the gear box located at the bottom on the steering column.
Asked in Isuzu
What problem of Isuzu 4BA1 engine the manual trnsmission noisy in second gear only?
a noisy second gear in your transmission is that your second gear might have broken gear tooth which is mostly the problem with my cars.either the second gear on the counter gear or the second gear itself. ...
Asked in Technology
Does an idler gear change the speed of the driver gear?
No. But if there are two idler gears, one smaller than the other, say a 12 tooth and a 6 tooth. the 12 tooth idler is the idler of the driver gear which has 24 teeth, making the idler gear rotate 2 times for every rotation that the driver gear rotates. Now, if the 12 tooth idler gear is rotating 2 times faster than the driver gear, then the 6 tooth idler gear will rotate 2 times faster than the 12...
Asked in Toyota Tacoma
What is the gear ratio of a 2001 Toyota Tacoma 4X4?
The gear ratio of a 2001 Toyota Tacoma 4x4 ranges from 3.15 to 4.56 depending on the configuration. This ratio determines the number of times the wheels turn in relation to the engine and transmission. ...
Asked in Toyota Trucks and SUVs
What is the stock gear ratio for 1989 Toyota 4wd pickup?
the stock Toyota gear ratio is 4.11
Asked in Toyota 4Runner
What causes shifter to pop out of gear on 1990 Toyota 4runner?
If you have a manual transmission, it may need a new plastic bushing at the bottom of the shifter. My 1991 Toyota pickup kept slipping out of gear due to a deteriorated plastic bushing. I picked up a new bushing at the local Toyota parts department for around $11. ...
Asked in Differentials
How do you calculate a gear ratio of a 9 tooth Drive gear?
Number of teeth on driven gear divided by teeth on driven gear.
Asked in Math and Arithmetic, Units of Measure, Physics
How do you use a gear teeth vernier calipers?
One can use gear tooth vernier calipers by first setting the instrument's chordal addendum on the addendum vernier. After this, one should straddle the gear tooth with the caliper, bringing the tooth together until no jiggling about can be felt anymore. ...
How do you calculate a gear ratio of a 5 tooth drive gear and a 15 tooth driven gear?
You take driven divided by drive. 15 divided by 5 is 3. So the ratio would be 3:1 ...
Asked in Honda Motorcycles
Why does a 1983 Honda CT110 chatter in third gear only third gear at any speed up shift or down?
Third gear could have a broken tooth, chipped tooth or bent tooth on the gear and only makes a noise when it has drive pressure applied to it, so either way when pressure is applied it makes a noise. ...
Asked in Volvo 240
1993 Volvo 240 that makes a single clunk right as the engine turns over Otherwise it runs and idles fine What could cause this clunk?
If it doesn't repeat the sound while the engine is running, especially accelarating or decellerating, it is probably related to the starter pinion gear or the flywheel/flexplate ring gear. When the starter gear engages the flywheel/flexplate, there is a small portion of gear tooth missing. It starts to catch and slips, slamming into the next gear and then engaging. Eventually, you'll lose another and yet another tooth, producing a dead spot to an extent the car won't start. ...
Asked in Toyota Tercel
Where do you find the filling plug for the gear oil on a 1992 Toyota Tercel?
where do you find the filling plug for the gear oil on a 1993 Toyota tercel ...
Asked in Toyota SR5
Will a box from a 1987 Toyota Pick up fit on a 1992 Toyota pick up?
what kind of box? if you meen a gear box it will work if they have the same motors and the same goes for a engine controll box ...
On a timing chain where do the timing notches on the gears go top top or top bottom?
Answer ON THE TOP GEAR, NOTCH ON BOTTOM. ON THE BOTTOM GEAR, NOTCH ON TOP. You really need a manual for the engine in question so you know exactly where the timing marks must be. The above answer may not be correct for all engines. ...