0
If you are talking about a LAN, then just making sure that all devices and cables are capable of gigabit speeds.
Wiki User
∙ 14y ago
Add your answer:
Earn +20 pts
Which ethernet card can handle gigabit network traffic?
You would need the ethernet card can handle gigabit network traffic cable.
If you want to upgrade your 100BaseT Ethernet so that it will run about 10 times the current speed what technology would you use?
You would want to move to a Gigabit network. This will require a switch capable of Gigabit speeds, network cabling capable of Gigabit speeds (Cat 5e for example), and a network interface on a computer that is also Gigabit rated. Most modern switches are Gigabit rated (even inexpensive soho switches).
Why used gigabit Ethernet lan?
You would use gigabit ethernet in a LAN where you want speed; otherwise, most LANs run at 100 megabits per second, which is considerably slower.
What is the minimum cable requirements for Gigabit Ethernet?
Cat 6 network + guide to networks Chapter 5 Review Question 5
Why would a realtek 8168 LAN card not work at 1gbit speed even though it says that in the manual?
In order for you to achieve gigabit data rates, you need: * A gigabit Ethernet card (as you have) * A gigabit router * Cabling that is of correct length and quality to carry a gigabit signal. If these conditions are not met, the card will drop to the next available transfer rate.
Differences between Ethernet Fast Ethernet and Gigabit Ethernet?
The 'Ether' part of Ethernet denotes that the system is not meant to be restricted for use on only one medium type, copper cables, fibre cables and even radio waves can be used. Fast Ethernet Network was developed as an upgrade to traditional Ethernet Networking. Fast Ethernet improved traditional Ethernet by increasing transfer rates 10 times, from 10 Megabit to 100 Megabit speed. Gigabit Ethernet Network is an upgrade on Fast Ethernet Network equivalent to Fast Ethernet Networks improvement over Fast Ethernet Network, offering speeds of 1000 Megabits (1 Gigabit) Cisco have a good document with diagrams and a reasonable amount of depth that answers your questions on 10/100/1000 Ethernet. See related link. Ethernet card would be 10Mbps (mega bauds per second) Fast Ethernet card would be 100Mbps. Most ethernet cards sold today are Fast Ethernet or better. Look for the 100Mbps or the 10/100Mbps specification. The only difference between the both is the speed. Hence both cards are basically the same using the same technology except the fast Ethernet card can run on 10/100mb/s, an astonishing speed. Original 10Base2, 10Base5 and 10baseT Ethernet (thin coaxial cable, thick coaxial cable and twisted pair, respectively) specifications offered a 10Mbit/second throughput (data transfer rate). Although 1 Byte is 8 bits, 10Mbits in practice doesn't mean 1.25MBytes/second, because there's some extra information transferred. On average it can be seen as a ~1MByte/second link speed. Then new standards appeared, some of them exotic (like 100VG AnyLan), but the new Ethernet standard was 100baseTX, which used twisted pair (like 10baseT, but with slightly higher quality requirements - Category 5 cable). It has been called Fast Ethernet, as it offered 100Mbit/sec transfer speed, a 10-fold improvement. Usually all the network equipment can talk both 10baseT and 100baseTX (for example network switches have "10/100" ports). But this was not enough - then came a next speed-up: the 1000baseTX, still running on twisted pair, but with even higher cable quality requirements, offering 1000Mbit/s transfer speed, thus called Gigabit Ethernet: 1000 Mega = 1 Giga.
Why would your laptop need an Ethernet adapter?
If you ever plan to connect your laptop to a wired network, you will need an ethernet adapter. If you never plan to plug it in to a network or if you will always use wireless, an ethernet adapter is not necessary.
Is Ethernet faster then ADSL?
Even a slow Ethernet network would be faster than ADSL, since 10baseT LAN networks run at 10 Mbps. An ADSL connection typically tops out at around 8 Mbps. However, if you are talking about throughput, then they might be very close, since Ethernet has problems with packet collision. Then again, most Ethernet networks today for LANs run at 100 Mbps, which would place it far faster than ADSL based on speed measurements. However, ADSL does not use the same transmission method as Ethernet, but Ethernet will still be faster than ADSL (especially if you consider the Gigabit speeds).
What would be the best cable to use if you are installing GigaBit Ethernet?
A cat5e should work up to 1 gig. Cat6 is optimal but more expensive and harder to wire.
Which is the type of 10-gigabit ethernet that can carry signals the farthest at nearly 25 miles?
It would be 10Base-ER. It has a maximum rang of 40 Kilometers witch is 24.4 miles.
What type of 10-gigabit ethernet can carry signals the farthest nearly 25 miles?
It would be 10Base-ER. It has a maximum rang of 40 Kilometers witch is 24.4 miles.
Which network device has the capability of amplifying and regenerating network signals but has no capability of routing or segmenting?
I would say an ethernet extender/booster/repeater.
