0
Want this question answered?
Be notified when an answer is posted
Add your answer:
Earn +20 pts
How to install new electrical wire?
Call a qualified electrician.
How do you install a new ground wire for a 1986 Ford F150?
Just ground the wire with a screw straight on to the frame!
Free guide to wire a 30amp twist lock plug?
Check out Related Links below
How long does it take to install and wire new outlets?
long enogh to eat dinner and forget about it
You want to install a new light fixture in your bathroom upon removing the old fixture down you discover there is no grounding wire only a black and white wire and GFCI outlet on the circuit?
Just install the new fixture with black to black, white to white, and cap off the ground wire on the new fixture. It'll be fine.
How do you install a ground wire in a car?
Bolt it to the frame.
What is lock wire?
Lock wire or safety wire is applied in situations where extreme mechanical reliability is needed. Aircraft use a lot of lockwire to secure fastners. So do aerospace companies and a lot of car and bike racers. Here's how it works.Imagine a bolt and nut. Now imagine the bolt having a hole drilled through it near the end of the threads away from the head. Put the bolt in the bolt hole using washers if needed and fit the nut. Tighten it up. Now do the rest of the bolts and nuts that hold this cover in place. You now have all these bolts with a little bit of their threads sticking through the nuts, and the hole we talked about is visible. Take a long piece of flexible wire - lock wire - and put it through one hole. Then twist it to the point where it reaches another bolt and put the wire through the the hole in that bolt. Repeat until all the fasteners are lock wired. Even if a nut or multiple nuts come loose, they can't get off the bolts because of the lockwire. Sometimes bolt heads are drilled for lock wire and it's put through the heads of the fasteners, twisted and then secured.Use the link to pictures and see what's up.
Where does the ground wire go on a 1965 chevy c10?
There is usually a bolt hole in the alternator/generator bracket. I believe it is either a 3/8" or 1/2" hole. Stock, the ground wire goes here with a bolt, lock washer, and nut. If you have an engine that has the alternator on the opposite side of the engine from the battery, use one of the existing bolt holes in the front of the cylinder head closest to the battery. Use a bolt and lock washer to install. In either scenario, be sure to clean off the paint where the cable end is going to touch the metal. This will ensure a good connection. I tend to use 0 gauge wire for my ground wire. A little bit of overkill, but I like to have a good ground.
How do you remove alternator on 2000 cougar?
It should be the same as for a 2002 Mercury Cougar which is answered in WikiAnswer under the Question; " How to remove alternator from a 2002 Mercury Cougar 2.5L V6." The 2000 Cougar may be different by having an upper alternator BOLT. If it does, and you can't lift the bolt out (after fully loosening the bolt), lower the alternator and you can, then, lift the bolt out. When you begin to install the alternator (attach the power wire, and the wire connector) place the BOLT in the upper hole in the alternator, and THEN, raise the alternator to install.
How to change a speed sensor on a Honda Accord?
what year is it? is it a four or a v-6? vehicle speed sensors are usually on top of the transaxle. there is a wire harness and a bolt. unplug, remove bolt, reverse to install.
How do you change an alternator in your 1995 gs300 Lexus?
2JZ-GE Engine # Disconnect the negative battery cable. Wait at least 90 seconds before performing any other work. # Remove the engine undercover. # Turn the drive belt tensioner clockwise and remove the drive belt from the engine. # Disconnect the generator electrical connector. # Remove the rubber cap and nut and then disconnect the alternator wire. # Disconnect the alternator wire clamp from the wire clip on the alternator. # Disconnect the A/T coolant hoses and bracket from the alternator by removing the bolt and pipe clamp. # Remove the alternator bolt, nut, pipe bracket and then remove the alternator from the engine. To install: # Install the alternator and pipe bracket. Torque the bolt and nut to 27 ft. lbs. (37 Nm). # Install the A/T oil cooler pipes to the alternator and install the bolt and pipe clamp. # Connect the alternator wire clamp to the wire clip on the alternator. # Connect the electrical wire to the alternator and install the nut. # Install the alternator electrical connector. # Install the drive belt. # Install the lower engine cover. # Connect the negative battery cable. # Start the engine and check the charging system for proper operation
Where are the wire cutters on cryptids island?
There are no wire cutters (that is an item from 24 Carrot Island).The bolt cutters are in Puerto Rico, at the upper left star on the map. Go to the right, past the house, and climb the springy poles to reach the top. You need the bolt cutters to cut a lock at New Jersey.
How do you install an ignition switch on a 1966 Mustang?
disconnect the battery.put the key in the switch,and turn to the acc position.(on) insert a piece of wire into the hole of the lock cyclinder.push the wire inward to depress the the lock pin,then turn the key counter clock wise and with draw the lock cyclinder.press the rear of the switch and rotate it counter clockwise. remove the bezel,switch and spacer.hope this helps.
Can you install a GFCI on a 2 wire circuit?
Yes, you install a GFCI on a 2 wire circuit.
How do you change the ignition lock cylinder for a Toyota Camry 1998?
You have to remove the plastic cover underneath of the steering wheel, after that the metal shield behind the plastic cover. When you remove the shield you will get access to the ignition lock cylinder. Disconnect the wire harness, remove the cylinder, install a new cylinder. Connect the wire harness, install the shield, install the plastic cover. PS: Before start write down the code for your stereo (if you have one), disconnect the negative cable from the battery. Be careful when you work around the air bags.
How do I install sparkplugs wire for a 1998 kawasaki ninja 600 R?
how do I install sparkplugs wire for a 1998kawasaki ninja 600R
What size wire to use to install a thermostat?
Use what is called bell wire or thermostat wire.
