0
What else can I help you with?
What type of light bulb should I use for my fixture that requires a G type bulb?
You should use a G type light bulb for your fixture that requires it.
Do you hook up white or black first when changing a light fixture?
As the power to the light fixture should be, and hopefully is off, it does not matter which you hook up first.
How can I remove a dome light fixture?
To remove a dome light fixture, first turn off the power to the fixture. Then, carefully remove the screws or clips holding the fixture in place. Gently pull the fixture down from the ceiling, being mindful of any wires connected to it. Disconnect the wires, and the fixture should come off easily.
How do you wire 2 3-way switches to control a single light fixture?
To wire 2 3-way switches to control a single light fixture, you will need to connect the switches in a specific way. The power source should be connected to the first switch, then a traveler wire should be connected between the two switches. Finally, the light fixture should be connected to the second switch. This setup allows you to control the light fixture from either switch.
How do you replace the light fixture on an in ground swimming pool that doesnt have enough cord to bring it out of the pool?
The whole fixture should be replaced and the new one installed properly. There should be enough cord wrapped around the light in the niche to bring it up to the pool deck. You could drain the pool down, but I don't recommend it. When I see this condition, I don't take chances, I replace the whole light, cord, etc. Its not something to fool around with if you don't know what your doing. A: Call a qualified swimming pool electrician. He will bring the pool light and all related items to the light fixture up to code. This is not a job for an ammature.
Why is indoor light fixture hot to the touch and light bulbu blows?
The light fixture may be hot to the touch because the bulb wattage is too high for the fixture, causing it to overheat. This can lead to the bulb blowing. Make sure to use bulbs with the correct wattage for the fixture to prevent overheating.
What size light fixture should I choose for my room?
When choosing a light fixture for your room, consider the size of the room. For a standard 12x12 foot room, a light fixture around 24 inches in diameter is recommended. Larger rooms may require a bigger fixture, while smaller rooms may need a smaller one.
When hanging a pendant light fixture over a kitchen sink how far out from the wall or window should it hang?
Far enough that it does not blind you when you are working at the sink and not so far as to cast a shadow. 12" to the center of the light is perfect.
How do you remove the tail light lens from a 1989 Chevy Celebrity?
The tail light lens on a 1989 Chevy Celebrity is part of the tail light fixture and cannot be conveniently removed. If you want to change a light bulb you have to remove the tail light fixture from the car. To remove the tail light fixture: 1. In the trunk next to the quarter panel are three nuts, remove the center nut. It should be in the center of the tail light fixture. 2. Pull the tail light fixture so that the stud comes out of the body, then pull outward to pull the tab out of the backup light fixture. 3. You can now take the appropriate socket out and replace the bulb. Reverse the steps to replace the light fixture.
What should I do if my buzzing light fixture is causing a disturbance in my home?
If a buzzing light fixture is causing a disturbance in your home, you should first turn off the power to the fixture and check for loose connections or faulty wiring. If you are not comfortable doing this yourself, it is best to contact a licensed electrician to inspect and repair the fixture to ensure safety and prevent further issues.
Is a fluorescent light grounded?
If you are talking about the lamp then the answer is no. If you are talking about the fluorescent fixture, it should be. It is the fixture grounding that helps the tube to ignite. because of the close proximity to the metal of the fixture. There are many occasions when the fixture will not operate, but as soon as the ground is connected the fixture operates fine.
What are the steps involved in a light fixture installation?
The steps involved in a light fixture installation include turning off the power, removing the old fixture, connecting the wires, attaching the new fixture, and testing the light.
