0
If an AC source has a frequency of 100Hz what is the time for 1 cycle?
Wiki User
∙ 14y agoWant this question answered?
Be notified when an answer is posted
Add your answer:
Earn +20 pts
Is frequency the time required for one complete cycle?
Frequency is 1 divided by the time required for each cycle.
If you triple the frequency of a vibrating object what will happen to its period?
There are two basic characteristics of harmonic motion: amplitude and frequency. Frequency can be looked at in a couple of ways. One is the number of cycles in a given unit of time (like cycles per second), and the other is the length of time it takes for one complete cycle of the motion, the period (like seconds per cycle). As the frequency increases, the time it takes for one cycle decreases. If there are more cycles per unit time, then it will take less time per cycle of the motion. That's an important concept. The two are inversely proportional. For a given motion, if its frequency doubles, then it takes half as long for one of the cycles to occur. The period is cut in half because the frequency had doubled. Following that logic, if the frequency of a harmonic motion is tripled, the period will be one third the period of the original motion.
If you triple thr frequency of a vibrating object what will happen to its period?
frequency is the inverse of time: 1/f=t therefore if you increase frequency by 3 the time (or cycle) will be 1/3
A mass oscillates on the end of a spring with a period of 4.0 seconds. What is the frequency of the oscillator?
This sounds like a homework question, so rather than doing your homework for you, I'll explain how to find the answer for yourself.The period and the frequency are very easy to find from the information provided. First, remember the definitions of period and frequency:Period is the amount of time per oscillation.Frequency is the number of oscillations per unit time.When you see the word "per" in these definitions, you should think division, because that is how you find the answer. When we say period is time per oscillation, this means time divided by oscillations. So your period is obtained by dividing the amount of time (in seconds) by the number of oscillations in that time. The units will make sense this way too: time divided by oscillations will give you a number that means seconds PER oscillation, which is what period is!Similarly, frequency is oscillations per time, so take the number of oscillations and divide it by the number of seconds it took. Your units will be oscillations per second, which makes sense for a measure of frequency.
What is the period of 10 kHz?
To calculate the time of the cycle you just invert the Hz value. Hz = 1 / T, Where T is the time of the cycle in seconds so a 10,000Hz signal has a time of each cycle of: 0.0001 seconds.
Is frequency the time required for one complete cycle?
Frequency is 1 divided by the time required for each cycle.
What is the frequency of a signal which has a cycle time of 100 microseconds?
the frequency is 1 divided by the cycle time, or 1/100 microseconds = 10,000 cycles per second
What is the frequency of a sine wave that has a cycle time of 1ms?
1kHz
What is the difference between natural frequency and natural cyclic frequency?
numbers of cycle per unit time.
What is the relationship between frequency and period?
Time period = 1 / frequency. Frequency = 1 / time period.
If a signal has a frequency of 100 HZ and a phase of 180 degrees how much time has the wave been offset from 0?
The period - the time for one full cycle - is the reciprocal of the frequency. If the frequency is in Hz, the time will be in seconds.From 0 to 180 degrees is one-half of a full cycle.
Difference between period frequency and duty cycle of a waveform?
Not sure about duty cycle of a waveform. The frrequency is the inverse of the period and the period is the inverse of the frequency. Frequency (it pains me to tell you) is measured in Hertz, cycles per second. Period is the time for one cycle or seconds per cycle. If we let f be frequency and T be period, then f=1/T and T= 1/f
Does water cycle takes place all the time?
No, it does'nt. In the morning, the sun is the source that drive the water cycle. But at night, no heat source are available to drive the water cycle.
If you triple the frequency of a vibrating object what will happen to its period?
There are two basic characteristics of harmonic motion: amplitude and frequency. Frequency can be looked at in a couple of ways. One is the number of cycles in a given unit of time (like cycles per second), and the other is the length of time it takes for one complete cycle of the motion, the period (like seconds per cycle). As the frequency increases, the time it takes for one cycle decreases. If there are more cycles per unit time, then it will take less time per cycle of the motion. That's an important concept. The two are inversely proportional. For a given motion, if its frequency doubles, then it takes half as long for one of the cycles to occur. The period is cut in half because the frequency had doubled. Following that logic, if the frequency of a harmonic motion is tripled, the period will be one third the period of the original motion.
The length of time between a point in one cycle and the same point in the next cycle of an ac wave is the?
this is called time period of the wave. it is also the inverse of frequency of wave.
The time it takes to complete one cycle of a signal is known as?
The time it takes to complete one cycle of a signal is called one period. For example, if the signal has a frequency of one hertz (one cycle per second), the period would be 1 second. A two hertz frequency would mean a ½ second period, or ½ second to complete one cycle.
What is the frequency?
Frequency is defined as the number of cycles per minute. Ex: for a sine wave from " 0 to pi " is a cycle, and this repeats periodically within a interval of time. if frequency of a signal is 50Hz, then you can say that this signal repeats 50 time's a minute..
