0
If one bulb fails and all the others turn off you are dealing with a?
Wiki User
∙ 7y ago
A circuit of a series configuration.
Wiki User
∙ 7y ago
Add your answer:
Earn +20 pts
Why bulb does not work when fitted in a circuit with switch?
because you are switch the hot leg, so it can be turn on an off.
What do you need to make a simple series circuit to light a bulb?
To make a simple series circuit to light a bulb, the simplest components are a power source (such as a battery); a switch (to turn the power on or off); the bulb (obviously !); and some wires to connect everything together.
What type of a circuit do flashlights use?
A flashlight is a series circuit. The batteries positive end connects to the flashlights switch. The switch connects to the center pin of the light bulb. The bulb filament is connected to the center pin of the bulb and the outer metal shell of the bulb socket. The shell of the bulb socket is connected to the metal flashlight's body which returns to the negative end of the battery. Turn on the switch and you have light.
What is meant by cold resistance of filament lamp?
It means exactly what it sounds like. The resistance of an incandescent bulb's filament depends on its temperature. A filament has a positive temperature coefficient, which means that its resistance increases as its temperature increases. A typical 40 watt bulb (120 volts) has a cold resistance of about 28 ohms, but its hot, operating resistance is about 360 ohms. If the cold resistance were constant, the bulb would dissipate 379 watts. In fact, cold turn on is the most stressful time for a bulb.
Why does Fluorescent bulb not light and end turns black?
In order to know why fluorescent bulbs turn black at the end, you need to understand how they work. Basically, when you turn on the lighht switch, the ballast sends a spark through the mercury-vapor-filled tube or bulb, depending on design. When it does this, it creates light by activating phosphors that coat the inside of the tube. Well each time the ballast fires, it creates emissions. These emissins materials then settle on the surface inside the glass. After awhile this material piles up. When it does this, the tube end turns completely black. Not only does the tube end turn black, but the accumulated materials pile up so high that it blocks the electrons that flow into the mercury. When this happens, you will notice the bulb or tube flicker heavily and then burn out.
Why does your left turn signal work and the right fails?
Is one of the bulbs on the right burnt out? In this case, it is surely a bulb issue so check all turn-signal related bulbs on the right side. See sources and related links below for correct bulb information.
2002 ford expedition front turn signal blink to fast and the rear signal don't blink at all?
your rear bulb is blown - replace the bulb The turn signal blinks fast because the bulb is going out. That is also why the others dont blink.
Why does the left turn signal flash quickly?
check your fuse and bulb as well as the others bulb in your car. - its just electrical nonsense. easily sorted In my experience, when one signal flashes quickly, that means that a bulb has burnt out on that side.
Which bulb is the turn signal in the rear tail light assembly?
the bulb with two elements in it is the turn signal and brake light bulb
How do you replace the turn signal bulb located on a 1998 Audi A6?
On the 1998 Audi A6, the turn signal bulb can be replaced by opening the hood. Reach into the turn signal from the fender wall and push in and turn the old bulb to remove it. Push in and turn to replace with a new bulb.
When you turn off an electric bulb in your home do all the others light go out?
No, not in my home. In my home, all of the lights and outlets are wired in parallel, so no light affects any of the others.
How do you change a turn signal bulb?
how do you change a rear turn signal bulb on a 2010 buick lucerne
2005 Montana turn signal bulb change?
The front turn signal light bulb can be accessed through the engine compartment. Take hold of the light bulb connector on the back of the turn signal. Push the connector in and turn at the same time. The light bulb will come out.
How do you change the turn signal light bulb for a 2006 mitshubishi endeavor?
Remove the turn signal light bulb connector. Take hold of the light bulb, push in and turn at the same time, to remove the light bulb. Reverse the process to install the new light bulb.
How do you change your driver side front turn signal bulb in a Mazda 6?
There is a gray tab on the back of the headlight assembly turn it counterclockwise and pull it out the bulb is on the end push in the bulb then turn it counterclockwise and pull the bulb free. The bulb you need to use is a #2357A its not that hard to do.
How do you replace the front turn signal bulb located on a 1999 Honda Civic?
Turn the wheel to the left if changing the passinger side bulb and to the right if changing the drivers side bulb. Remove the pop out plug holding on the plastic wheelwell cover, reach in and turn the bulb holder a quarter turn, replace the bulb and re-assemble.
2002 Chevy cavalier turn signal bulb replace?
How do you replace a turn signal bulb in a 1998 cavalier
