0
If stair tread is 7 inches and run is 11 inches will there be a 1 inch overhang?
Wiki User
∙ 15y ago
A "tread" and a "run" are the same thing. Your question negates itself. However, if what you meant was an 11" riser and a 7" tread, then what you are describing is a ladder, as it would have an angle greater than 50 degrees. Ideally, you should reverse the dimensions, in which case then, yes, a 1" overhang is appropriate.
Wiki User
∙ 15y ago
Add your answer:
Earn +20 pts
What is the proper overhang for a stair tread over the riser?
No more than 1-1/4 inch.
Why is the head length on a drywall T square 22 inches long?
You bought a chinese one. Mine are all 24 inch.
A spider crawls though an arc of 50 degrees. How far does the spider crawl if the diameter of the circle is 100 inches?
There are 360 degrees around a circle. So first find the circumference of the circle and then divide it by 360 which will give 1 degree of distance and then multiply this by 50 to show how far the spider crawled: Circumference = 100*pi 1 degree = (100*pi)/360 = 5/18*pi Distance crawled = 50*5/18*pi = 43.6332313 inches Answer: 44 inches to the nearest inch.
What is the circumference of a 12 inch round circle in pi?
The circumference of a 12-inch round circle in pi is: 12pi
What is the correct arc length for arc welding?
3/8 inch
What is the proper overhang for a stair tread over the riser?
No more than 1-1/4 inch.
How many inches must a tire tread be?
Depending on location and vehicle size, tread depth must be at least 2/32 inch or greater.
What are the overall lengths of a 1966 Chevy C10 Long and Short Bed?
The 1966 Chevrolet Truck (C10-C14/K10-K14) has the following dimensions: Short Wheelbase 115 inch - wheelbase 186.75 inches - overall length 63.1 inches - front tread 61.1 in - rear tread Long Wheelbase 127 inch - wheelbase 206.25 inches - overall length 63.1 in - front tread 61.1 in - rear tread
How wide in inches is a size 30 950 r15 tire?
30 inches tall, tread width of 9.5 inches, on a 15 inch diameter rim.
What size are 245 70 15 tires in inches?
That's approximately 9 and 1/2 inches across the tread. There are 25.4 mm in an inch
The stair tread depth is typicaly how many inches more than the run so that it sticks out?
The 'nosing' of a tread is typically 25-30mm(1-1 1/4").This measurement is taken from the face of the riser. The 2006 International Residential Code (IRC) states the information about stairs below. You should check with your local building department to verify applicability. R311.5.3 Stair treads and risers. R311.5.3.1 Riser height. The maximum riser height shall be 7¾ inches (196 mm). The riser shall be measured vertically between leading edges of the adjacent treads. The greatest riser height within any flight of stairs shall not exceed the smallest by more than 3/8 inch (9.5 mm). R311.5.3.2 Tread depth. The minimum tread depth shall be 10 inches (254 mm). The tread depth shall be measured horizontally between the vertical planes of the foremost projection of adjacent treads and at a right angle to the tread's leading edge. The greatest tread depth within any flight of stairs shall not exceed the smallest by more than 3/8 inch (9.5 mm). Winder treads shall have a minimum tread depth of 10 inches (254 mm) measured as above at a point 12 inches (305 mm) from the side where the treads are narrower. Winder treads shall have a minimum tread depth of 6 inches (152 mm) at any point. Within any flight of stairs, the largest winder tread depth at the 12 inch (305 mm) walk line shall not exceed the smallest by more than 3/8 inch (9.5 mm). Hope this helps! TL North, CBO
How many inches of thickness is the tread on most off-road mud tires?
Tread is measured in 32nds of an inch, or x/32. Most off-road mud tires measure about 18/32, which is read as "eighteen thirty-seconds of an inch."
What is 632 Tread Depth?
6/32 inch. it is a measurement of tread depth.
For year-round tire care and hazard prevention you should be sure that your tires have at least A 1 8 inch tread B 1 16 inch tread C 1 4 inch tread?
For year round tire care and hazard prevention you should be sure that your tires have at least 1/8 inch of tread.
On a set of stairs the rise is always bigger than the run?
That would be incorrect! The International Residential Code (2006 IRC) states the following: R311.5.3 Stair treads and risers.R311.5.3.1 Riser height.The maximum riser height shall be 7¾ inches (196 mm). The riser shall be measured vertically between leading edges of the adjacent treads. The greatest riser height within any flight of stairs shall not exceed the smallest by more than 3/8 inch (9.5 mm).R311.5.3.2 Tread depth.The minimum tread depth shall be 10 inches (254 mm). The tread depth shall be measured horizontally between the vertical planes of the foremost projection of adjacent treads and at a right angle to the tread's leading edge. The greatest tread depth within any flight of stairs shall not exceed the smallest by more than 3/8 inch (9.5 mm). Winder treads shall have a minimum tread depth of 10 inches (254 mm) measured as above at a point 12 inches (305 mm) from the side where the treads are narrower. Winder treads shall have a minimum tread depth of 6 inches (152 mm) at any point. Within any flight of stairs, the largest winder tread depth at the 12 inch (305 mm) walk line shall not exceed the smallest by more than 3/8 inch (9.5 mm). Riser would be the height (7 inch MAX) and run (10 inch MIN) would be the tread depth. Therefore, the run is greater than the rise by not less than 2 1/4 inches. Hope this helps! Exactly the opposite. The run is always longer than the rise. If you go with a longer (or bigger) rise than the run, you will wind up with something that resembles a ladder. Try to keep your rise between 6 and 8 inches, and your run between 10 and 12 inches. Hope this helps. Memory jogger The convenience store we all know of is 7-11. Got it? It's 7-11. A 7 inch rise and an 11 inch run works for most stairs. Oh, and that's a door hanger's code, too. The top hinge is about 7 inches down from the top of the door, and the bottom hinge is about 11 inches up from the bottom of the door.
What is the minimum tire tread thickness in PA?
Tire spec in PA is 2/32 of an inch of minimum tread
What is the minimum tire tread for a passager vehicle?
Minimum LEGAL tire tread depth is 2/32nds of an inch.
