Radiators
Jeep Cherokee Laredo
Jeep Grand Cherokee Laredo

If there is not a radiator cap on a 1991 Jeep Cherokee Laredo where do you put the water?

272829

Top Answer
User Avatar
Wiki User
2005-09-22 08:14:29
2005-09-22 08:14:29

in your coolent overflow tank then squeeze the upper radiator house to pump it through the rest of the radiator and to the engine.

1
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
๐Ÿ˜‚
0

Related Questions

User Avatar

I need to know asap how to remove a trasmission oil pan on a 1991 jeep Cherokee Laredo? Thank you!

User Avatar

I have a 1991 Jeep Cherokee Laredo, in the manual it tell you to use 10W30, and that's what I have been using, hope this helps.

User Avatar

The value of a 1991 Jeep Grand Cherokee Laredo will depend on the condition of the vehicle. The vehicle in average condition with 100,000 miles is worth an estimated $914.00 dollars.

User Avatar

The diagram for replacing a serpentine belt for the 1991 Jeep Cherokee Laredo is located on the front of the vehicle inside the engine compartment. You can also find this diagram in the Chilton's manual for this vehicle.

User Avatar

It is on the end of the engine facing the radiator. 2 bolts to take off. 1 is from the hose coming off the top radiator hose and the other is a heater hose. on my jeep Laredo the bottom nut is hard to get off because the belt is in the way. . Check the very top hose coming off the radiator and follow it it should take you to the thermostat.

User Avatar

try unscrewing the back light covers and replacing the lights

User Avatar

Do you have a 4L 6 cyl.? if so, there is NO automatic choke. It is controled by computer and sensors.

User Avatar

kelly blue book it. it gives all different type of prices depending on what you want to do with it. kellybluebook.com

User Avatar

considering the fact, that i recently just searched it up. the gapping is about .35hope that helps

User Avatar

first check the front end steering. idler arm is usually the culprit.

User Avatar

A 1991 Jeep Cherokee computer is what fits a 1991 Jeep Cherokee.

User Avatar

On a 1991 Cherokee Laredo, it's on the underside of the car towards the rear of the car on the drivers side, almost parallel with the rear wheels. It is bolted to the underside of the car using a bracket with two screws which are probably rusted solid. Good luck.

User Avatar

Depending on what transfer case is used, most of the time, yes they will fit.

User Avatar

Loosen up the power steering pump and pull on pump till belt is tight.

User Avatar

Chiltons Auto Manual for Jeep Cherokees has diagrams for each of the jeep fuse boxes

User Avatar

paste this into your browser...i could not get the link box to take.. but this should ansewr the question on the o2 sensor

User Avatar

try replacing the crankposition sensor my 89 did the same thing and that is what fixed it for me.

User Avatar

the water pump is right behind the radiator and is belt driven. Also try to check the coolant reservoir by having it pressure tested

User Avatar

i have an 89 and mine did the same thing try replacing the crank position sensor.

User Avatar

It should fit but, the crank position sensor produces a signal by referring to the flex plate. In 1991 Jeep went to a Chrysler fuel injection system and the windows that the crank sensor reads are different. So in other words it should bolt up but then it will not start.

User Avatar

It is on the front of the engine,it has the fan for the radiator on it.

User Avatar

Cherokee - 1991 is rated/received certificates of: USA:G


Copyright ยฉ 2020 Multiply Media, LLC. All Rights Reserved. The material on this site can not be reproduced, distributed, transmitted, cached or otherwise used, except with prior written permission of Multiply.