0
If you purchased a new key ignition cylinder and misplaced the keys buying the same party can you use those keys Or replace the whole thing?
Wiki User
∙ 15y ago
Replace. Keys are not the same
Wiki User
∙ 15y ago
Add your answer:
Earn +20 pts
How do you know if your key is bad 1992 Cadillac?
If the key will turn in the ignition cylinder, the only other fault the key can have is a missing or damaged resistor. The resistor is in the middle of the key and looks like a small black oval. The resistor has one of 16 specific values and is "read" by the Pass-key module. If you have a vehicle with 30K or more on the odometer that won't start, and everything else is good, (battery, starter etc…), the most likely problem is the two little wires that connect the Pass-key module to the ignition cylinder. These wires have to flex each time the cylinder is turned and eventually break at the ignition cylinder. The only reliable repair is to replace the ignition lock cylinder and key. New Ignition lock cylinders do not come with real ignition keys, only a temporary key to identify the cuts. If the cylinder is changed you have to purchase a new key separately to match the old key resistor and then cut to match the new lock cylinder.
How do you fix a leaking slave cylinder on 87 Jeep Cherokee Does it have to be replaced?
Yes, replace it.
How do you replace the plug on an appliance?
Plugs/cords can be purchased from appliance parts stores like www.appliancepartspros.com. Usually on the bag it will tell you how to replace. It is usually just a couple of screws.
Where is the brake relay and how do you fix cylinder 5 misfire 1997 Jeep Grand Cherokee help please.?
Run a compression test, especially on the cylinder that is misfiring. If the compression is up, it's either the ignition or if the vehicle is manifold injected it could be the #5 injector. If you suspect ignition, try the plug, distributor cap or the wires. Can I run a compression check myself? If so how? If not would it be in my best interest to just replace the plug wires cap and rotor first? About the brake question, I meant brake switch not relay, brake lights are not working, not bulbs not fuse what else could it be? Look at the switch at the bottom of your brake pedal. It might have come loose or has shorted out.
How do you string an Epiphone bass guitar?
When one purchases an Epiphone bass guitar, it should have the necessary strings. If the guitar needs new strings, it is best to have a professional replace the strings or follow the manual received when the guitar was purchased.
How do you replace ignition lock cylinder Isuzu rodeo?
How I can replace ignition switch cylinder from Isuzu Rodeo?.
Can you replace the ignition lock cylinder on a 1994 Pontiac firebird without removing the steering wheel?
You can replace the ignition lock cylinder in your 1994 Pontiac Firebird without removing the steering will. Remove the retaining ring at the top of the ignition cylinder. The ignition cylinder will slide out.
How do you replace 1981 Chevy ignition cylinder?
== ==
Do you need to replace the ignition lock cylinder when you replace the ignition switch on a Pontiac Sunfire 1999?
No, not if it is not defective. If the ignition switch is defective then that is all you need to replace.
How Do You Replace Ignition In 1992 Cavalier?
how do you replace ignition switch on a 1992 Chevy cavalier 2.2 4 cylinder
How to fix a 1996 Pontiac grandam ignition locked?
Replace the ignition lock cylinder.
How do you replace an ignition lock cylinder on a Chevy S-10?
Remove the retaining ring at the top of your Chevy S 10 ignition lock cylinder. Slide the ignition lock cylinder out. Remove the wiring harness from the back of the ignition lock cylinder. Reverse the process to install the new ignition lock cylinder.
How do you remove and replace an ignition lock cylinder on a 1994 Ford Bronco?
Begin by removing the retaining ring at the top of your 1994 Ford ignition lock cylinder. The ignition lock cylinder will slide out. Remove the wiring harness from the end of the ignition lock cylinder. Reverse the process to install your new ignition lock cylinder.
How do you replace the ignition lock cylinder on a 2004 Honda civic?
The ignition lock switch is found under the steering column on a 2004 Honda Civic. Remove the steering column and ignition switch. Loosen the mounting screws that hold the cylinder in place. Pull and replace the lock cylinder.
Why escalade ignition switch does not turn?
The tumblers in the key cylinder have most likely become stuck in the wrong position and you will have to replace the ignition key cylinder.
How do you replace ignition lock cylinder on a 1996 Mercury Tracer?
Begin by removing the retaining ring at the top of your 1996 Mercury Tracer ignition switch. The ignition lock cylinder will slide out. Remove the wiring harness from the end of the cylinder. Reverse the process to install your new ignition lock cylinder.
How do you replace ignition lock cylinder on a 2004 Chevy aveo?
I broke my key in the ignition and cant get it out. My only option I can see, is to replace to tumbler. How do I remove it?
