answersLogoWhite

0


Best Answer

You can replace the ignition lock cylinder in your 1994 Pontiac Firebird without removing the steering will. Remove the retaining ring at the top of the ignition cylinder. The ignition cylinder will slide out.

User Avatar

Wiki User

โˆ™ 2014-11-20 00:13:07
This answer is:
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
User Avatar
Study guides
๐Ÿ““
See all Study Guides
โœ๏ธ
Create a Study Guide

Add your answer:

Earn +20 pts
Q: Can you replace the ignition lock cylinder on a 1994 Pontiac firebird without removing the steering wheel?
Write your answer...
Submit
Related questions

How do you replace the ignition cylinder 1992 Bonneville?

I have not seen a way to do it without removing the steering wheel (and airbag).


How do you remove the ignition lock cylinder on a 1973 Firebird?

pull steering wheel off, remove the steering lock disc, then remove the signal light switch assembly to gain access to the retaining screw that holds the lock cylinder in place,


How do you remove the power steering cylinder from a 1965 nova?

Begin by removing the hose from your power steering cylinder. Remove the power steering cylinder retaining bolts. The power steering cylinder will come off.


Someone tried to stesl your 1989 firebird and broke the steering column how do you repair this without taking it apart or do you have to?

If the steering column is broken on a 1989 Firebird, it may have to be taken apart to be repaired. If it is only the ignition that the thieves damaged, a new ignition can be installed.


1988 gmc safari Steering column switches and ignition key lock cylinder replacement?

1988 gmc safari Steering column switches and ignition key lock cylinder replacement?


How do you replace the ignition lock cylinder on a 2004 Honda civic?

The ignition lock switch is found under the steering column on a 2004 Honda Civic. Remove the steering column and ignition switch. Loosen the mounting screws that hold the cylinder in place. Pull and replace the lock cylinder.


Replacing the ignition lock cylinder on 2000 Cadillac Catera?

how do you get ignition switch out of steering column in 2000 catera?


Why would a 1991 Pontiac Firebird not start after you replaced the steering column?

Because when you change the ignition in a firebird you have to use the same key and key lock that was on the original column. If you don


Key in steering wheel won't turn?

You have to replace the ignition key cylinder.


Why won't my 1988 325i BMW ignition switch won't turn?

Maybe your steering wheel it's keeping the ignition cylinder to turn, so move the steering wheel and at the same time try to turn the key. Maybe you need to replace the ignition cylinder key lock


What part is needed when the steering wheel locks?

Usually you have replace the ignition key cylinder.


98 Camry ignition removal?

The process of removing a 1998 Toyota Camry ignition switch requires taking apart the steering column and lower dash, as well as several of the under-dash relays. The ignition switch is connected to the key cylinder and cabin wire harness. A faulty ignition switch will prevent the car from starting.


How do you know if ignition switch is in lock position?

the steering wheel will lock and the key will come out, unless of course the ignition cylinder is broken


If the key does not work to start the car must the whole ignition cylinder be taken out?

If the Ignition switch is faulty, all you need to change is the switch module, not the lock cylinder. Normally removal of the switch module, is just a matter of removing a couple of screws. Replacement of the steering lock and ignition switch assembly, is usually only required following an auto-theft.


How do you replace the ignition of a 1992 Lincoln Town Car?

To replace Ignition Switch, first you have to remove the old one. To do this you disconnect battery ground cable. Remove the upper steering column shroud by removing the five self-tapping screws. Remove tilt steering column lock lever, Remove lower steering column shroud, disconnect the ignition switch electrical connector, turn ignition switch lock cylinder to the "run" position, remove the two screws retaining ignition switch, and finally unhook the ignition switch from the actuator. Now to install the new one.Make sure that the ignition switch lock cylinder is in the "run" position. You can test for the "run" position by rotating the ignition switch lock cylinder approximately 90 degrees from the "lock" position. Hook up the ignition switch into the actuator. You might have to move the ignition switch slightly back and forth to align the ignition switch mounting holes with the lock cylinder housing threaded holes. Install retaining screws. Connect electrical connector to ignition switch. Connect battery ground cable. Check ignition switch for proper operation, including start and accessory positions. Also, make certain that the column is in the "locked" position. Then Install upper steering column shroud. Install the lower steering column shroud and tilt steering column lock lever.


How do you change the ignition cylinder on a 1991 Cadillac Eldorado?

Remove steering wheel and signal switch


How do you change the ignition cylinder on a 1987 Olds 98?

you will need to pull the steering wheel and column cover then it will be simpl to pull out cylinder and replace it.


Where is the ignition switch on a 95 cutlass supreme?

The ignition switch(not to confused with the ignition key lock cylinder)is located on the steering column under the dash.Some models can be a little tricky to reach.Most would be accessible by dropping the steering column.Not a hard job to do.


How to replace ignition switch on a 1995 Dodge pickup?

Remove the plastic covering on the steering column. The ignition switch is the box that the ignition cylinder runs into. It's basically easy with only removing a couple of bolts to replace. The only trick is to be very careful actually pulling the box off the column. Make sure the key is in power off position. wiggle the box off, when putting the ignition cylinder into the new ignition switch you don't want to turn the key. Leave it in the off position. Then watch the rod in the rear of the new ignition switch as it goes back into the column. I have seen people have to turn the key in the ignition cylinder while pushing gently into the ignition switch. But beware it can turn into a real nightmare. If you use a bran new ignition cylinder, it will state all over do not turn the cylinder until it's installed.


Remove ignition lock cylinder 2006 chev cobalt?

The ignition lock cylinder on a 2006 Chevy Cobalt is removed by popping off the steering column cover and inserting a screwdriver into the release hole. The cylinder can then be pulled from its housing and replaced.


What would cause a steering wheel to lock up?

Most likely it's a faulty ignition cylinder.


How do you remove key switch Ford Contour?

how do I remove the key switch from a 1998 ford contour You have to remove the plastic trim around the steering column (behind the steering wheel). Put the key in the ignition cylinder and turn one click. There is a small hole on the side of the ignition cylinder, stick a small screwdriver into this hole and press hard. Pull out the ignition cylinder with the key.


How do you replace the ignition lock cylinder on 3rd gen camaro?

First take off the steering wheel. Next Take the steering colum wheel lock off by removing the snapring. Next take all of the screws out of the blincker/dimmer switch. Then there should be a bolt/screw directly located where the cylinder lock is . Remove it, turn your key into the start position and pull out.


How do you replace ignition lock cylinder on a 97 Saturn wagon?

I found the easiest way to do it is by first removing the cover ovet the steering column(a few screws). You then need a long flat blade srew driver. Insert the old key into the cylinder and look for a "button" on top. Depress the "button" with the screwdriver and pull the cylinder out. Just slide the new cylinder in.


How do you replace the ignition cylinder on a 1987 Chevrolet van If you need a special tool where can I get it or can I improvise Is replacing the cylinder and steering wheel going to be a problem?

You will need a steering wheel puller and a steering lock removal tool You rent them at yourlocal auto parts store