Mazda 626

In a 1995 Mazda 626 FS engine what do you need to swap from auto trans to manual trans?

121314

Top Answer
User Avatar
Wiki User
2008-05-23 12:47:36
2008-05-23 12:47:36

A lot. Obviously the manual tranny, ull also need the clutch pedal, a new brake master cylinder since the manuals uses the same container as the brakes. Mit need new drive shafts not sure A lot. Obviously the manual tranny, ull also need the clutch pedal, a new brake master cylinder since the manuals uses the same container as the brakes. Mit need new drive shafts not sure

1
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
๐Ÿ˜‚
0

Related Questions

User Avatar

take the bolts out and it should come out take the bolts out and it shold come out

User Avatar

i have a 96 suburban with the same engine,owners manual says 7500 lbs (4l80 trans)

User Avatar

The automatic transaxle fluid dipstick is between the engine and the battery ( the manual transaxle does not have a dipstick )

User Avatar

NO , the 2.0 L - 4 cylinder engine in a 1995 Mazda 626 ( IS NOT) an interference engine ( according to Gates - they make timing belts etc. )

User Avatar

1994 - 2005 Mazda Pickups Repair Manual lists a Power Control Module (PCM) located on the passenger side of the engine compartment, along the upper edge of the firewall.

User Avatar

automatic trans fluid. Mercon works fine.

User Avatar

hi.. I have a geo metro 1.0 1995 my engine computer is: 3392050G20 FED M.T (manual trans) anyway u can check out in www.ecmecu.com/geo. victor.

User Avatar

A 1995 Mazda 626 with the 4 cyl engine requires 3.5 quarts of oil, and the V6 engine needs 4 quarts.

User Avatar

The 1.8 litre four cylinder engine in a 1995 Mazda Miata has a timing BELT

User Avatar

manual trans it doesn't have a filter, only the automatics have one.

User Avatar

Can you tell what can kind of mazda we talking about (model) ?

User Avatar

the manual tells you to pull the whole engine don't take off a lot of the larger pieces and all motor mounts lift the engine about 3-6 inches remove the trans out the top it wont fit through the wheel well because of the sub frame and axle without a lot of work

User Avatar

hi.. I have a geo metro 1.0 1995 my engine computer is: 3392050G20 FED M.T (manual trans). annyway u can check out in www.autoecmecu.com/geo. victor.

User Avatar

Knowing the firing order of a car's engine can help with engine issues later. The firing order for a 1995 Mazda Miata is 1-3-4-2.

User Avatar

The 95 200SX S14 is OBD1 EDIT the 95 200sx 1.6Liter engine manual trans is odbII says right on the underside of the hood.

User Avatar

The 1.5 Liter engine takes 3.4 US Quarts (3.2 liters) and the 1.8 Liter engine takes 3.8 US quarts (3.6 liters). Source: 1995 Owner's Manual #8F85-EA-94E

User Avatar

instructions on how to install engine valve cover gaskets on l996 Mazda mpv van with 3.0 engine.

User Avatar

You really don't know what you are asking for. Get a manual on your car for the engine and a separate one for the trans. You need mega amount of special tools to do either and a whole lot of experience.

User Avatar

The timing marks for a 1995 Mazda e2000 are located on the cam and crankshaft sprockets. They must be perfectly aligned to prevent engine damage.

User Avatar

No. The engine, and especially the automatic transmission used in 626's, aren't built to withstand the additional stresses placed on them by a turbo or supercharger.

User Avatar

On the 1995 Mazda 626 v6 engine you will find the proper oil listed on the transmission dip stick. Do not overfill

User Avatar

The 1995 Mazda air conditioner dryer is located on the firewall in the engine compartment. The air conditioner dryer can be found on the passenger side of the firewall.


Copyright ยฉ 2020 Multiply Media, LLC. All Rights Reserved. The material on this site can not be reproduced, distributed, transmitted, cached or otherwise used, except with prior written permission of Multiply.