0
In a 220 volt AC single phase circuit the voltage from either leg to the neutral is?
Wiki User
∙ 14y ago
The proper terminology is L1,L2,N. N is for neutral and it is this wire that is grounded. The voltage measurement from the L1 to N will give you 120 volts. Also from L2 to N will give you 120 volts and as you know from L1 to L2 will give you 240 volts. Single pole breakers in the panel board starting at the top, alternate between L1 and L2 all the way down to the bottom. These breakers all have 120 volt outputs. If you plug a 2 pole breaker into two slots then you get 240 outputs because L1 and L2 are adjacent to one another.
Wiki User
∙ 14y ago
Add your answer:
Earn +20 pts
How three phase line current convert in single phase?
The current is the same in the three live wires. The voltage can be described as the line voltage (phase to neutral) or the phase voltage (phase to phase) which is larger by a factor of sqrt(3). So a line voltage of 230 v corresponds to a phase voltage of 400 v.
What is the relationship between the voltage output at the interface and the voltage across the series and parallel circuit?
Ohm's law states that the current in a circuit is inversely proportional to the circuit resistance. There is a single path for current in a series circuit. The amount of current is determined by the total resistance of the circuit and the applied voltage.
What happens when you disconnect a neutral at source in a three phase system?
== == == == It is true. Damage will most likely result somewhere, maybe not everything. When a neutral on a multi-wire circuit is opened (open-circuited) (removed) (cut) while things are under load, the voltage will change at the loads. Some loads will get more than normal, some will get less. The damage usually occurs on the side that gets MORE voltage. For example: your TV may be on a circuit that goes from 120volts to 50 volts, while your light bulb goes from 120volts to 180volts and blows. It all depends on how "balanced" the circuit is. In theory, if the loads are perfectly balanced then the neutral is not needed. In reality loads vary constantly, therefore, the voltage will vary if the neutral is open-circuited. That means running with an open neutral is something that anyone with any smarts at all will not do. It is absolutely possible to damage equipment by opening the neutral in some circumstances. As always, if you are in doubt about what to do, the best advice anyone should give you is to call a licensed electrician to advise what work is needed.If you do this work yourself, always turn off the powerat the breaker box/fuse panel BEFORE you attempt to do any work ANDalways use an electrician's test meter having metal-tipped probes(not a simple proximity voltage indicator)to insure the circuit is, in fact, de-energized.IF YOU ARE NOT ALREADY SURE YOU CAN DO THIS JOBSAFELY AND COMPETENTLYREFER THIS WORK TO QUALIFIED PROFESSIONALS.
What happens if phase wire touch to earthing?
When a phase line touches the neutral by any conducting material means the Short Circuit. If there is a short circuit then the current in that circuit will be much higher and this increase in current may damage the the devices that are connected to that line.
A capacitive device in a single phase ac circuit causes the current waves to?
Lead the voltage waves
What will happen if single phase load is connected to three phase circuit?
To obtain a single-phase supply from a three-phase supply, the single-phase load must be connected either (a) between any pair of line conductors, or (b) between any line conductor and the neutral conductor. Of course, the voltage obtained from either of these connections must match the voltage rating of the load.
What is a single circuit?
is the measured voltage,generated between a line voltage and the starting point of a three phase transformer, which is the neutral point. Answer: it is an ac circuit in which the supply has a live and neutral wire, usually at one of the standard voltages 110/120v or 220/240 v. A three-phase circuit is a combination of three single-phase circuits with the phases of the voltages 120 degrees apart so that they peak in a regular sequence.
How three phase line current convert in single phase?
The current is the same in the three live wires. The voltage can be described as the line voltage (phase to neutral) or the phase voltage (phase to phase) which is larger by a factor of sqrt(3). So a line voltage of 230 v corresponds to a phase voltage of 400 v.
How do you wire a three phase four wire generator for single phase output?
In a three phase four wire system - voltage between any one phase and the neutral is single phase. Hence the single phase equipment or load between any one phase and the neutral.Another AnswerA single-phase load can be connected either between any line conductor and the neutral conductor, or between any pair of line conductors. The choice is dependent on the voltage rating of the load, which must match either the phase voltage (line-to-neutral) or line voltage (line-to-line) -these values will be indicated on the machine's nameplate.
How does voltage change across an appliance in a parallel circuit?
With the minor voltage loss in the wiring, the voltage drop across a single appliance is the total voltage in the circuit, and doesn't change when more devices are added in parallel.
What is the relationship between the voltage output at the interface and the voltage across the series and parallel circuit?
Ohm's law states that the current in a circuit is inversely proportional to the circuit resistance. There is a single path for current in a series circuit. The amount of current is determined by the total resistance of the circuit and the applied voltage.
How does the voltage of a double battery compare to the voltage of a single battery?
The voltage depends on how the two batteries are connected to one another. If they are connected in a series circuit (positive end to negative end) the voltage will double. If they are wired in a parallel circuit, (It
Can you use 3 phase circuit as 3 separate single phase circuit?
yes we can use as a single phase circuit because at practise directly the 3-phase circuit is made by combining the three single phase circuits
How many wires do you need for a 208 v circuit?
208 v is a three-phase supply voltage used in North America, carried on a 4-wire system. The voltage between one of the three live wires and the neutral wire is 120 v and a single-phase supply can be taken by using one live and the neutral. If in doubt about the connection consult an electrician.
What happens when you disconnect a neutral at source in a three phase system?
== == == == It is true. Damage will most likely result somewhere, maybe not everything. When a neutral on a multi-wire circuit is opened (open-circuited) (removed) (cut) while things are under load, the voltage will change at the loads. Some loads will get more than normal, some will get less. The damage usually occurs on the side that gets MORE voltage. For example: your TV may be on a circuit that goes from 120volts to 50 volts, while your light bulb goes from 120volts to 180volts and blows. It all depends on how "balanced" the circuit is. In theory, if the loads are perfectly balanced then the neutral is not needed. In reality loads vary constantly, therefore, the voltage will vary if the neutral is open-circuited. That means running with an open neutral is something that anyone with any smarts at all will not do. It is absolutely possible to damage equipment by opening the neutral in some circumstances. As always, if you are in doubt about what to do, the best advice anyone should give you is to call a licensed electrician to advise what work is needed.If you do this work yourself, always turn off the powerat the breaker box/fuse panel BEFORE you attempt to do any work ANDalways use an electrician's test meter having metal-tipped probes(not a simple proximity voltage indicator)to insure the circuit is, in fact, de-energized.IF YOU ARE NOT ALREADY SURE YOU CAN DO THIS JOBSAFELY AND COMPETENTLYREFER THIS WORK TO QUALIFIED PROFESSIONALS.
What happens if phase wire touch to earthing?
When a phase line touches the neutral by any conducting material means the Short Circuit. If there is a short circuit then the current in that circuit will be much higher and this increase in current may damage the the devices that are connected to that line.
Is thermocouple voltage used for battery charging?
No, as the voltage of a single thermocouple is very low , you need a thermopile (thermocouples connected together) and a circuit to get a readable voltage at the other end.
