0
In a highly inductive circuit if is small capacitance is added in series then the angle between v and you will be?
Wiki User
∙ 11y ago
lagging
Wiki User
∙ 11y ago
Anonymous
increases
Add your answer:
Earn +20 pts
What is the process of circuit design?
The circuit design process covers systems ranging from highly complex to simple. The design process for simple circuits can usually be completed by one person, while teams of designers may be required to complete the process for more complex circuits.
How does a isolating transformer work?
Isolation transformers are used to isolate one circuit from another. Highly sensitive circuits may require isolation from high power circuits, for example.
How works oil circuit breakers?
A circuit breaker is a safety device that is put in an electrical circuit. When something fails, or shorts out, the circuit breaker "senses" the excessive current and automatically opens (or breaks) the circuit. They are used in homes, as well as some electrical devices. They are different than a fuse in that a circuit breaker can be reset. A fuse on the other hand, has to be replaced once it opens up. I hope this helps you. for more info, here is a web page about circuit breakers: <a href="http://www.wisegeek.com/what-is-a-circuit-breaker.htm">Ciruit breakers</a>
Where you use diodes in domestic?
as diode allows current to flow only in one direction . it is highly used in the conversion ac to dc power supply as in chargers, voltage converters... also used in circuit isolation, as it does not work in reverse biased mode.
What is N-well in VLSI?
An N-well in VLSI is a deep zone of highly N-type doped semiconductor, usually used to create reverse biased isolation junctions between components.
Why capacitor banks are not recommend with generator sets?
A generator is a highly inductive device with low resistance. Capacitors are, well, capacitive. when you have an inductor near a capacitor, you can get ringing. This is known as ferroresonance. The capacitance and inductance form an LC tank circuit, which causes excessive overvoltages. Generators are typically high impedance grounded, which contributes to ferroresonance issues.
What is difference between lpf and upf wattmeters?
LPF wattmeter is used for measuring power in highly inductive circuits & UPF wattmeter is used for measure power in resistance circuit in which the power factor ranges from 0.5 to unity. Answer is given by :Er. M KUMAR YADAV
Highly inductive load as a constant current source?
An inductor is a device that resists a change in current. The equation is di/dt = v/L. This means that inductors are current sources, and given a sufficiently large inductor, in comparision to the circuit, it is a constant current source.
What is AC23?
Alternating Current for highly inductive load i.e. motors...whereas AC21 is for resistive load....i.e. heating elements. this is what you called utilization category...
Causes of low power factor methods of improving power factor?
using highly inductive loads may lead to reduction in the power factor. or consumption of unappreciable amount of power also results in the same. methods to improve PF . using synchronous condensers using capacitor banks using ow inductive loads
What is the highly vascular structure that acts as a communication between the mother and the embryo?
The highly vascular structure that acts as a communication between the mother and the embryo is called the placenta.
What is difference between enzyme and receptor?
Enzyems are highly selective catalysts. Receptors are not very highly selective catalysts.
High level short circuit?
The short circuited path is the one which doesn't have any distributed elements(i.e., resistors, inductors,etc...). So the highly short circuited means only 'the connecting wire' is present in the circuit.
Differentiate between a highly modified and least modified ecosystem in terms of productivity?
Highly Modified: Its highly modified Least Modified: Its Least modified
Is it meant to be between marny clulow and Shia LaBeouf?
Highly doubtful....
What is the difference between Knockwurst and Hot Dogs?
Knockwurst are highly seasoned.
What is the process of circuit design?
The circuit design process covers systems ranging from highly complex to simple. The design process for simple circuits can usually be completed by one person, while teams of designers may be required to complete the process for more complex circuits.
