0
What else can I help you with?
What do you need to remove in order to remove the carburetor from your 1996 Yamaha Virgo 750?
remove the manifolds first you my want to remove the seat firat
How do you rerplace turn signal stalk?
You have to remove the upper and lower panels from the steering column, remove the bolts that hold the stalk in place and unplug. Install in reverse order.
Removing a 98 civic headlight assembly?
You need to remove the bumper cover in order to get at the lower bolt for the headlight assy.
How do you change shocks on a 1995 roadmaster?
raise front end of car- use jackstands if lift is not availble. remove two bolts securing lower part of front shock to the lower control arm . remove nut securing the top of the shock to the frame. remove shock through hole in lower control arm. install new shock in reverse order.
Where is the plug to drain the transmission fluid in a 1997 Voyager 3.0?
There is no plug. You have to remove the pan to drain the oil. Loosen all the bolts and remove the lower ones first and let the oil flow into a container placed underneath. Measure the drained oil in order to have an idea as to how much to fill.
How do you change front struts 1995 Ford Aspire?
First, Take off the front tire. then remove the brake caliper, remove the brake disc, undo the bolts connecting the strut to the lower control arm, undo the bolts under the hood and remove. use spring compressors to get new one on and do the rest in reverse order.
How do you replace the bushing on the lower control arm?
remove everything in order to get the arm ready to come off,remove tire, calpier assy, shock, sway bar, knock lower arm loose loose from spindle, vehicle jacked up of course, lower arm ,remove two bolts where control arm is mounted to frame, hammer and cold chicel to remove bushings, revser of it put back all you have taken loose.
You need to remove the power steering pump Do you remove pulleypumpbracket first then try and get pulley off repair manual says remove pulley first but removal tool too long to fit.?
There is a bolt that is blocked by the pulley. In order to remove the pump you need to remove that bolt. So you need to remove the pulley first to get access to that bolt.
How do you remove the Heater Coil on a 1989 Dodge Spirit 4-cylinders Automatic?
First you have to remove the Upper and Lower Hoses going into the firewall, those hoses goes to the heater core... you must remove the bottom half of the dash in order to access the heater core... it should be held in with about 4 bolts (im not really sure how many bolts holds it in).
How do you you replace fog lights on 2004 Subaru Forester?
Front Fog Light AssemblyREMOVAL # Disconnect the ground cable from battery. * Remove the two clips and lower mudguard. * Disconnect the harness connector. Remove the lower bolts. # Remove the mounting bolts and clip, and then detach the fog light assembly. INSTALLATIONInstall in the reverse order of removal. Front Fog Light BulbREMOVAL # Remove the front fog light assembly. Remove the back cover. # Remove the spring retainer, and then detach the fog light bulb. INSTALLATIONInstall in the reverse order of removal.
How do you change the timing chain on a 98 5.7 vortec?
First you will need to drain the coolant, then remove the upper and lower radiator hoses. Next you will need to remove the ac compressor and put it aside.(Do not disconnect the hoses or you will lose all of the refrigerant). Then you will need to remove the alternator. (Disconnect the battery first!!) Then remove the bolts that hold the 2 major brackets holding the PS pump and the alternator (set them aside as well) you can leave the PS pump bolted to the bracket. then you can remove the fan and the water pump. then you can remove the lower pulley and you will need a special puller to remove the harmonic balancer. Make sure you put a bolt in the crankshaft before using the puller so you don't mess up the threads. You will also want to lower the oil pan by loosening the bolts and letting it drop about a half inch. Then remove the timing cover. Rotate the crankshaft until both dots on the lower gear and upper gear are pointed at each other. Now you can remove the upper gear, lower gear and chain. Just reverse this order to reassemble. Also, you will want to mark the bolts and all electrical connections so that you know where they go. You will probably have to replace the timing cover if it is a plastic one. Once you have finished reassembling everything, I strongly recommend changing the oil. Also, these items do not have to be removed in this order, you can remove the items in whatever order you want. I have found this to be the easiest. Hope this helps you.................. Avdgolfer.
Where are the bolts located on the back seat of my 1993 Dodge Spirit in order to safely and undamagingly gain entrance to the trunk?
Push the lower seat inward towards the trunk and lift up. this will allow you to remove the lower seat. Once this is done you can gain access to the lower bolts for the back of the seat. remove these bolts and then lift the back of the seat up and out.
