0
In which circuit did screwing out one bulb not influence the lighting of the other bulb?
Wiki User
∙ 13y ago
A parallel circuit will not effect the other bulb. If the bulbs are in a series circuit the other bulb will not turn on.
Wiki User
∙ 13y ago
Add your answer:
Earn +20 pts
Can one use 1 circuit of a 3 wire plus ground 2 circuit cable as a GFI circuit with the other as a lighting circuit?
A GFCI can not be used on a three wire branch circuit. It has to be on a single two wire circuit.
A 32A breaker was controlling a lighting circuit but is now on a 6A breaker which is now buzzing what should you do?
Answer for countries in Europe and other world areas running a 50 Hz supply service.Depending on the load of your lighting circuit. I would measure the current with an inductive amp meter. once you know the current required for your lighting circuit, you then install a circuit breaker which is 15% higher than your load. eg, load is 10A. 10A load + 15 % = 12A breaker (15 A is ok as the breaker is used to protect the wiring and should be rated in consequence of your wiring by 25% less or its current rating, or less, not the load)The humming of your lighting circuit breaker indicates that your breaker is either faulty, or having a difficult time keeping a closed circuit. Or simply that the manufacturer produced a breaker that hums by nature of its construction.
An electrical circuit with components placed one after the other?
series circuit
What are all the parts on a circuit board?
to assemble a circuit you just need to connect one end of a wire to the battery and the other to the light bulb ( could be another electrical device) now take an other wire and connect on end of it to the other side of the battery and the other to the other side of the light bulb( or an other electrical device. if your circuit is including a switch this is how you do it: ( you will need three wires for this circuit if you have one electrical device) connect one end of the wire to the battery and the other to the switch.Grab another wire and attach one end of it on the other side of the switch and the other to the electrical device (light bulb). Grab another wire and attach one end of it to the other side of battery and the other to the other side of your electrical device. And there you have it how to assemble a circuit
What must you know before you change a circuit breaker?
Before you change a circuit breaker it has to be established that the breaker is at fault and not some other part of the circuit.
Can one use 1 circuit of a 3 wire plus ground 2 circuit cable as a GFI circuit with the other as a lighting circuit?
A GFCI can not be used on a three wire branch circuit. It has to be on a single two wire circuit.
How many smoke alarms can i put on an existing lighting circuit?
As a general rule, a lighting circuit should be lamped only for a maximum of 80 percent of the rated branch protection. So if it is a 15-amp circuit, you could put in fixtures for up to 12 amps, including any smoke alarms (assuming code allows anything other than lighting on that branch). Each smoke detector has a power consumption figure, if not also a required amperage. Add them all up and add that to the existing lighting to see if it is still under the 80 percent maximum design load.
A 32A breaker was controlling a lighting circuit but is now on a 6A breaker which is now buzzing what should you do?
Answer for countries in Europe and other world areas running a 50 Hz supply service.Depending on the load of your lighting circuit. I would measure the current with an inductive amp meter. once you know the current required for your lighting circuit, you then install a circuit breaker which is 15% higher than your load. eg, load is 10A. 10A load + 15 % = 12A breaker (15 A is ok as the breaker is used to protect the wiring and should be rated in consequence of your wiring by 25% less or its current rating, or less, not the load)The humming of your lighting circuit breaker indicates that your breaker is either faulty, or having a difficult time keeping a closed circuit. Or simply that the manufacturer produced a breaker that hums by nature of its construction.
Why do the lights in my home pulsate?
By pulsate do you mean flicker. A momentary dimming of your lights can be caused by motor loads on your lighting circuits. If your lights dim, this can be caused by a refrigerator, sump pump, garage door opener or other motors sharing the circuit with your lighting.
Does a Resistor have a different resistance when connected to a power source vs if the resistance is tested when the resistor is out of circuit?
In the circuit it is connected to other devices with their own properties that can influence your reading. Out of circuit you just measure the resistor. It has the same value both ways.
What is a flatblade screwdriver used for?
Screwing or unscrewing slot screws. It has no other use.
What happens if you put a 15 amp circuit breaker in a light circuit?
The circuit should be protected by a 15 A breaker.CLARIFICATION:If the wires and other components are capable of handling 15 amps (14 Ga wire or larger), you can safely protect the circuit with a 15 amp breaker. If the circuit is a non-standard lighting device for something other than typical residential application, you should contact an electrical engineer to help you determine the proper wiring and breakers.
Is quoizel lighting more expensive that other alternatives?
Quoizel lighting may be more expensive than other lighting, depending on where you shop. It is best to price the lighting at quoizel.com to determine if the price is within your budget.
Can you wire a stove using a neutral from a lighting circuit?
for USA, Canada and other countries running a 60 Hz supply service.No. On an existing installation, when replacing an appliance, you can continue to use the existing three wire circuit to feed the new stove or dryer.Another answerNo way can the neutral from a lighting circuit be used for a stove!Lighting circuits must only be used for lighting. Check your national electrical code and/or wiring regulations.For more information see the answers to the Related Questions shown below.As always, if you are in doubt about what to do, the best advice anyone should give you is to call a licensed electrician to advise what work is needed.Before you do any work yourself,on electrical circuits, equipment or appliances,always use a test meter to ensure the circuit is, in fact, de-energized.IF YOU ARE NOT ALREADY SURE YOU CAN DO THIS JOBSAFELY AND COMPETENTLYREFER THIS WORK TO QUALIFIED PROFESSIONALS.
What makes recess lighting different than other lighting?
Recessed lightning is different from other lightning because it addresses the need for more lighting. There are several different types of recessed lighting and each are for a different use. Such as task lightning which adds more lighting to an area such as over a sink.
What are the 10 signs of cheating?
I will put the answers as bullets1. You caught your significant other screwing someone else2. You caught your significant other screwing you and someone else at the same time3. You yourself are the cheater and are screwing someone4. You yourself are the cheater and are screwing your significant other and someone else5. Your finding used condoms on your bedroom floor and don't remember having sex. ( Although you could be having sleep sex)6. Your significant other doesn't count you as their significant other7. You are younger than your significant other (And your significant other is a prostitute)8. You haven't seen your significant other Ever! (Could be imaginary)9. Your significant other has more than one significant other10. Your significant other doesn't know that they are your significant other11. Someone is looking at your answers of the test before the test is graded.
Do lighting bugs eat other animals?
No,they feast on other plants.It's not like you roll over a dead animal and find Lighting Bugs in it.
