answersLogoWhite

0


Best Answer

start in the center and make circles outward tightening the front and rear last, then recheck tourque in any order 9 5 1 4 8 10 6 2 3 7

User Avatar

Wiki User

โˆ™ 2006-03-19 01:06:46
This answer is:
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
User Avatar

Add your answer:

Earn +20 pts
Q: Intake manifold tightening sequence
Write your answer...
Submit
Related questions

How do you know if your intake manifold gasket is bad?

You will feel a miss at idle and the idle speed may be erratic. Try retorquing the intake manifold bolts, working from the center out in the recommended tightening sequence. If that fails, the intake manifold will have to be removed and the intake gaskets replaced.


How do you know if Intake manifold gasket is bad?

You will feel a miss at idle and the idle speed may be erratic. Try retorquing the intake manifold bolts, working from the center out in the recommended tightening sequence. If that fails, the intake manifold will have to be removed and the intake gaskets replaced.


How can you tell if inlet manifold is faulty?

You will feel a miss at idle and the idle speed may be erratic. Try retorquing the intake manifold bolts, working from the center out in the recommended tightening sequence. If that fails, the intake manifold will have to be removed and the intake gaskets replaced


What are the torque specs and torque sequence for a 1992 Nissan Maxima intake manifold?

what are the torque specs and sequence for a 1992 Nissan maxima manifold


What is the Intake manifold torque sequence 455?

35 ft pounds


What is the torque spec for 1997 3.8 buick lesabre intake manifold?

The lower intake manifold to cylinder head torque specification is 132 inch pounds. The upper plastic intake plenum to lower intake should be done in three steps 22 inch pounds, 44 inch pounds and thirdly 89 inch pounds. Be sure to follow the appropriate tightening sequence diagram.


Coolant leaking from intake manifold?

leaking gasket try tightening the bolts a little might help


What is the torque sequence for intake manifold on a 1997 mercury cougar 4.6liter?

The 1997 Mercury Cougar 4.6 liter engine intake manifold torque sequence should begin at each end of the manifold. Keep moving towards the center and alternating from and to end.


How to replace intake manafold on V6 3800 engine?

Ineed the torque sequence and tightening specs for a 92 GM 3800 intake.


What is the torque specifications for the intake manifold on a 1997 Chevrolet vortec 350?

Install the lower intake manifold to the engine. Apply sealer, GM P/N 1052080 or equivalent, to the lower intake manifold bolts.Install the lower intake manifold bolts. Tighten the bolts in three steps:TightenTighten the bolts on the first sequence to 8 N·m (71 lb in).Tighten the bolts on the second sequence to 12 N·m (106 lb in).Tighten the bolts on the final sequence to 15 N·m (11 lb ft).I this is what you are looking for.GMmechanic@gmail.com


Intake manifold bolts torque ford windstar?

2000 3.8 Lower intake manifold (manifold to cylinder head) 1st step is 44 inch pounds, 2nd step is 89 inch pounds. This must be done in sequence.


Intake manifold torque setting for intake manifold?

diferential pressure sensor intake manifold plausibility


What is the torque sequence on a 351 Windsor intake manifold?

just start in the middle and tighten in circler pattern


What is the torque sequence for a 2000 5.7 intake manifold?

Start on the inside do an X pattern and work your way out


What is the tightening order for Chevy intake?

to tighten a intake manifold start with a center bolt and tigten in a circular pattern towards the ends. tighten bolts in even incraments until tight.


What is the Labor hours to replace a Chevy 3500 series intake manifold gasket?

It should take about an hour to change the intake manifold gasket. This part can be replaced by taking off the intake manifold cover, cleaning the old gasket off and sealing a new gasket in the space and tightening the bolts. When other things are in the way, like the alternator, it will take longer.


What is bolting sequence and torque on a 1989 Chevy 350 intake manifold?

the sequence is the two center bolts on each side, the work your way outwards


What are Torque specs for 1994 350 intake manifold?

Intake bolts should be torqued to 35 ft lbs in the appropriate sequence. There should be 12 total "intake" bolts


What is the torque specs for a 5.3 l intake manifold?

torque specs. on chevy sub for a 5.3L intake manifold and tighten sequence NEW ANSWER; step 1 is 44in-Lbs. then step 2 is 89in-lbs. That's it.


1995 olds 98 upper intake manifold torque sequence?

I found this in the local library that had chiltons manuals.


Where is the intake manifold gasket located?

between the head and intake manifold


Where is the intake manifold gasket?

Between the intake manifold and the cylinder head.


How do you change intake manifold on Isuzu trooper?

remove intake manifold.


Torque sequence 1996 5.7 gm intake manifold?

I just did an intake manifold job on a 1999 5.7L suburban. The intake manifold to the heads, note this sequence....from front to back on the passenger side 7,1,3,5......from front to back on the drivers side 8,4,2,6. Tighten # Tighten the bolts on the first pass in sequence (1-8) to 3 N·m (27 lb in). # Tighten the bolts on the second pass in sequence (1-8) to 12 N·m (106 lb in). # Tighten the bolts on the final pass in sequence (1-8) to 15 N·m (11 lb ft). Use Loc-tite blue on these bolts and follow the above sequence and torque levels.


What are the torque specs for a Pontiac 3.8 intake manifold?

I'm pretty sure this is that same 3800 motor that gm uses in my mom's 2001 buick Le Sabre. Her intake was the fiberglass resin plastic and the torque specs are 89 INCH pounds. Make sure you use the right tightening sequence too. 89 inch pounds is for the upper intake or Plenum. 136 inch pounds is the torque specs for the lower intake