answersLogoWhite

0


Best Answer

What is the question? If you mean the plastic coolant cross over, then it must be cracked. You have to replace the intake with Ford's modified one.

User Avatar

Wiki User

14y ago
This answer is:
User Avatar

Add your answer:

Earn +20 pts
Q: Intake plastic housing 96 crown vic police int?
Write your answer...
Submit
Still have questions?
magnify glass
imp
Related questions

Does the 2001 crown Victoria have an aluminun intake manifold?

No the 2001 Crown Vic does not have a aluminum intake , it has a composite plastic intake. as did all 96 to 01 Crown Vics. Starting in 02 Ford started using a different type of plastic intake with a aluminum front water crossover due to a class action lawsuit.


Where is the thermostat located in a 1991 crown Victoria ltd?

In a 1991 Ford LTD Crown Victoria ( 5.0 / 302 and 5.8 / 351 ) Follow the top radiator hose from the radiator , it connects to a housing on the front of the intake manifold . The engine cooling thermostat is inside the housing


If your 1999 Ford Crown Victoria has an antifreeze leak at the rear of the engine what could it be?

check your heater hoses one connects to the intake on rear passanger side of the motor it is likely the intake cracked there is a recall on this issue if the intake has been replaced with factory intake it is possible that the intake gasket is leaking check the bolts to be tourqed to specs if gasket is leaking replace gasket Crown Victoria Plastic Intake Manifold Heater Leak Fix When the stupidly designed intake manifold cracks where the heater pipe sticks into the plastic here's how to fix it. You will notice the plastic around the heater pipe is connected to some plastic to the front of the car from it. Take a hacksaw blade and cut about a 1/2" groove in that plastic - just enough to get a hose clamp around the plastic circle that holds the pipe. Tighten the clamp and voila! No more leak.


Where is the Mass airflow sensor located on a 1996 ford crown victoria?

On a 1996 Ford Crown Victoria : The Mass Airflow sensor should be between the engine air filter and the big rubber engine air intake tube ( I don't know if it is inside a plastic housing like it is on my 1995 Ford Explorer but you will see where the connecting wires go inside )


How do you remove stubborn thermostat bolts 1998 crown vic?

Allow the engine to warm up fully before unscrewing those bolts. If they break off in the brass inserts of the plastic intake, replace the intake.


Will a factory crown Victoria 96 motor fit a 99 police car?

Why not. Its either a 4.6 L or 5.0 L, same car same frame, just check the electronics. And by the way, if you do the job, change the intake on the 96, it still has the plastic cross over for the coolant. It will crack, if it already has not.


Where is the air flow sensor on a 2005 ford crown Victoria?

On a 2005 Ford Crown Victoria , the Mass Air Flow Sensor is in the top of the engine air filter housing just before it connects to the big engine air intake tube


How do you replace a thermostat on a 1995 Crown Victoria?

The thermostat is between a housing and the top of the engine, at the end of the upper radiator hose. There are two bolts on either side of the housing that need to be removed. The air intake (The black plastic cover, from the air filter to intake.) is in the way. There is one small bolt that needs to be removed (on the back/ passenger side) this should give you enough wiggle room to get at the housing bolt. Once the two bolts are removed, lift the housing out of the way and you will see the thermostat. Remove it and the gasket. Clean the surfaces if they require it, and place the new thermostat in. (the spring side goes into the engine) Replace the two bolts, and the air intake housing and you're done. (if you start the car and it won't idle, some vacuum hoses have become attached. re-attach and it will idle fine.)


What is the motto of Crown Point Police Department?

Crown Point Police Department's motto is 'To serve and Protect'.


When was Ford Crown Victoria Police Interceptor created?

Ford Crown Victoria Police Interceptor was created in 1992.


What does the Toronto police Crest Mean?

Wings = Industry Red Chevron = Housing Books = Education Staff = Commerce Crown = Coronation year in which the Municipality of Metropolitan Toronto was founded.


Is there a difference in a plain 97 crown vic transmission from a 97 crown vic police intercepter?

the 97 crown vic transmission is for the car and the interceptor is police car