0
No they are not. In fact a heat pump contains within it a heat exchanger/coil. A heat pump is reverse refrigeration. A heat exchange, exchanges heart from a heat source to a conditioned space (the area you want heated). While a heat pump uses a heat exchanger to supply heat to the conditioned space. Reverse refrigeration uses the air conditioner in reverse(you know how heat comes if the back of yhe air conditioner, well when it's in reverse that heat is used to heat a home in winter months.
Wiki User
∙ 12y ago
Add your answer:
Earn +20 pts
Heat exchanger for ammonia absorption refrigeration system?
there are two type of heat exchanger in absorption refrigeration, first is liquid heat exchanger and other is gas heat exchanger.both heat exchanger function is same, to transfer heat (hot medium to cold medium) without violate second newton law of thermodynamics. liquids heat exchanger is between boiler and absorber vessel mean while gas heat exchanger between evaporator and absorber.
Can Geothermal pumps be used for cooling?
Yes.The term geothermal heat pump is not the same thing as geothermal energy from hot springs. Here, it means a transfer of heat from the ground (in the winter) or to the ground (in the summer).
Can geothermal pumps can be used for cooling?
Yes.The term geothermal heat pump is not the same thing as geothermal energy from hot springs. Here, it means a transfer of heat from the ground (in the winter) or to the ground (in the summer).
Is a heat exchanger the same as having a furnace?
Heat exchangers are not indentical to furnaces. However, they do serve a similar purpose. Both heat exchangers and furnaces serve important individual purposes. They also aee ulilitzed for different devices.
Are refrigerant temperatures and pressures in the cooling mode of a heat pump about the same in both the suction side and the discharge side of the system?
Yes refrigerant temperatures and pressures in the cooling mode of a heat pump is the same. They are both in the suction side and the discharge side of the system.
Heat exchanger for ammonia absorption refrigeration system?
there are two type of heat exchanger in absorption refrigeration, first is liquid heat exchanger and other is gas heat exchanger.both heat exchanger function is same, to transfer heat (hot medium to cold medium) without violate second newton law of thermodynamics. liquids heat exchanger is between boiler and absorber vessel mean while gas heat exchanger between evaporator and absorber.
What is regenerator in mechanical engineering?
It is a heat exchanger that cycles the same fluid cooling it
What is different between cooler and heat exchanger?
Both the cooler and heat exchanger perform the same function as they remove heat from the engine. Two popular types of coolers are air-to-air inter-coolers that allow air to flow over fins and air-to-water models. The heat exchanger is often mounted in front of the radiator and uses airflow to reduce water temperature.
When should you use emergency heat?
During an emergency. i.e. when the heat pump is not working. If your heat pump can not keep your house warm, then the auxiliary heating coils (same thing as emergency heat) will come on automatically. If not, then there is a problem with your heating system.
What does the compressor on a heat pump do in heat mode?
The exact same thing it does in the cooling mode, the change between modes of operation does not take place in the compressor.
Function of heat exchanger?
There are actually many types of plate heat exchangers, and the YOJO brand has introduced brazed plate heat exchangers and gasket plate heat exchangers. Today is the home of brazed heat exchangers.Brazed plate heat exchangers have no headers, tie rods or sealing gaskets, and the plates are brazed at a temperature of 1100 ° C. During the assembly stage, a piece of brazing material (usually copper, and nickel) is placed between the two plates, the package is compressed, and then baked for several hour.BPHE is more compact and lighter, and the brazing material has the functions of both washer and frame. The intersection between the corrugations of the two coupling plates forms a dense network of contact points, which impart pressure tightness and generate vortex flow, thereby improving heat exchange. In this way, even at low nominal input speeds, the turbulence of the fluid is high, and for low flow rates, the fluid flows from laminar to turbulent.
How To Replace Your Heat Exchanger When Its Not Performing Up To Par?
The heat exchanger is very important to the operation of your boiler or furnace system within your home. This is the part that takes the heat and disperses it into the air or water for distribution of your home. If your current heat exchanger is not performing correctly, here is a simple guide to help you install a new one on your boiler or furnace unit. Step 1. When you are planning on installing a new heat exchanger, the first thing that you should consider is safety. Working with boilers and furnaces can be extremely dangerous. Little accidents, such as punctured hoses or disconnecting the wrong pipes that carry steam could cause you to get seriously burned. You should also wear protective work gloves because there is the potential of getting cut on sharp edges that may be present. Power to these appliances should be turned off at the main electrical circuit breaker. Since the furnace will be turned off, you should do this type of project in warmer weather conditions. Give these appliances enough time to cool down before proceeding. Step 2. If you are replacing an existing heat exchanger, you will first need to remove the old one. This is located behind a panel on your boiler or furnace appliance. Remove the panels located on the front of your furnace or boiler with a screwdriver. These panels can be extremely sharp and cause you injuries. To identify the heat exchanger, you will be looking for pipes and tubing coming off of what looks to be a bulky metal panel. You will need to write down where each of the pipes, clamps, hoses, or other part that is connected to the heat exchanger goes for easier re-connection. If it is possible to get a camera in there, you can also take a picture of the heat exchanger and its connections for future referencing. Remove all of the fittings that connect to the heat exchanger so that it can be removed from the furnace. Step 3. Reconnecting your new heat exchanger is very simple if you took good notes on the connection placements or took pictures of the old heat exchanger set up. If your heat exchanger kit has new fitting that need to be installed, you can replace the old ones with the new fittings. If the set up and fitting are the same, you can just replace the hoses, clamps, pipes and other hardware on your new heat exchanger. You will need to let your furnace sit for a few hours before you can replace the panels and turn the power back on to the furnace.
Is heat pump bettar than an electric heater?
A properly installed heat pump uses about one third of the electrical energy to produce the same amount of heat.
Can geothermal pumps can be used for cooling?
Yes.The term geothermal heat pump is not the same thing as geothermal energy from hot springs. Here, it means a transfer of heat from the ground (in the winter) or to the ground (in the summer).
Can Geothermal pumps be used for cooling?
Yes.The term geothermal heat pump is not the same thing as geothermal energy from hot springs. Here, it means a transfer of heat from the ground (in the winter) or to the ground (in the summer).
Is a heat exchanger the same as having a furnace?
Heat exchangers are not indentical to furnaces. However, they do serve a similar purpose. Both heat exchangers and furnaces serve important individual purposes. They also aee ulilitzed for different devices.
Advantage of shell and tube heat exchanger over double pipe heat exchanger?
**** you.......... pls somebody answer Double pipe heat exchanger consists of two concentric pipes of different diameters.One pipe is for hot fluid and another is for cold fluid.Both may have same flow direction(COCURRENT) and opposite direction(COUNTERCURRENT). Shell and tube heat exchanger consists of a shell in which large number of parallel tubes are present.One fluid hot or cold flow in shell and other hot or cold flow in the tubes. Also in case of shell & tube(S&T) the hot fluid will have more turbulence than in double pipe heat exchanger (HE) since there are no of tubes within a shell the area for convective heat transfer is considerably increased. so these are much more preferredTherefore the rate of heat transfer is greater in shell and tube because large surface area and enough contacting time
