0
pipe is measured up 12 inchs I.D. inside 12 and above are measured by O.D.if you measure 10" pipe you measure it from inside..12" and above measure from outside diametor
Wiki User
∙ 11y ago
Wiki User
∙ 11y ago10"
Add your answer:
Earn +20 pts
What is Id versus od size in copper fittings?
id means inside diameter, od means outside diameter, copper pipe and tubing is measured by the od, therefore the od the pipe or tubing will be the same as the id of the fitting
What is the diameter of an 8 inch pipe?
The inside diameter (ID) is 8 inches. The nominal pipe size (NPS) and outside diameter (OD) depend on the thickness of the walls of the pipe.
How can you calculate the ID of a pipe?
Can you calculate the ID of a pipe when you have the OD to be 10.75" and the wall thickness to be 0.5"Depends on what you know about it. If you have the outer diameter and you know the wall thickness, then ID = OD-2 x wall thickness
How can you get the weight for steel pipe?
assuming it's hollow. 10.68*ID*(OD-ID)
From which size onwards NB of pipe is equal to OD of Pipe?
14" and above
What is the size of the eagle?
what is difference between NB & OD in pipe size
How do I Find wall thickness of tube?
wall thickness of pipe is (OD - ID) /2
What is the technical difference between tube and pipe?
The primary difference between pipe and tubing is how the size is designated. Pipe is designated by a "Nominal Pipe Size" based upon the ID (inside diameter) of the most common wall thickness. Tubing is designated by the measured OD (outside diameter). For Example: A 3/4 inch iron pipe has an OD of 1.050 inches, while a 3/4 inch steel tube has an OD of 0.75 inches. The Copper industry calls all cooper tubular products "Tubes" but they designate a "Type". Each type has specified OD and ID dimensions The size of a tube is determined by it's OD and the thickness. The actual OD of a tube is just the same as it's nominal OD. A certain size of a tube will keep the same OD no mater what the thickness is. It is true for pipe except that the actual OD is larger than it's nominal OD. For example, for a 1" schedule 5s pipe, the actual OD is 1.315", the thickness is 0.065" and the ID is 1.185". When it's thickness is schedule xxs (0.358"), then it's ID is reduced to 0.599" while keeping it's OD. Furthermore, the actual OD of a pipe is just the same as it's nominal OD when the size is the same as or larger than 14" per ASME/ANSI B36.10/19 . Consequently, both the size of tube and pipe is measured by it's OD and the thickness. Actually tube is used when we need to transfer heat from its walls and we want this to be happen while in pipes we try to stop the heat transfer such as we use tubes in boilers because we make steam we need to transfer the heat while when we transport steam we use pipes because we wana save heat energy. 2: pipe can be thick according to formula d/t >10 while tube will must thin according to this formula. The Real Difference: Sorry to say; wrong! Pipe and tube is ever so simple. Pipes are used to transport something, and tubes to construct something; hence, tubes are defined by the od "outside diamater" and wt "wall thickness" (for construction stability), and pipes id inside diamater to allow a calculation for transportation viz., speed, volumes etc. (od = id + 2 * wt).
What is the difference between tubing and pipe?
The main difference between tube and pipe arises while considering the standard dimensions. The nominal sizes for pipes and tubes are determined differently. For pipes, the ID or Internal Dimension is the pipe size and for tubes the OD or Outer Dimension is considered the tube size.
What is the make up torque HT55 375 drill pipe?
it will vary by Tool Joint OD and ID. FYI 7"OD x ID 4" HT55 is 52,600 Ft lbs
What should be considered ID or OD when calculating pipe dia using volumetric flow rate?
Inside diameter
If you are fitting a pipe with a 10 34 OD into a 11 1516 ID what is the gap all the way around pipe is centered and how do you do it?
The gap is going to be 5/32 with the pipe centered. You could weld it.
