0
Is a pool pump motor drawing half the amps listed on its nameplate a problem with the windings?
Wiki User
∙ 10y ago
A pool pump motor which is drawing half the amps listed on its nameplate can indicate a problem with the windings or a lack of incoming current. Pumps will only draw as many amps as are required to operate under the current load.
Wiki User
∙ 10y ago
Add your answer:
Earn +20 pts
How much watts does a normal vaccine fridge use?
Check the nameplate on the fridge. If the wattage in not listed look for the voltage and amperage that is listed. The formula for wattage is amps times volts. This will give you the answer that you are looking for.
How many watts does a 4 slice toaster use?
On most appliances the number of watts is listed on a plate on the device. Turn the toaster over and look for how many watts it uses.
Will siemens breakers pass inspection on gould panel box?
As long as the breakers are made to fit the box, there shouldn't be a problem. you can only use breakers listed for the panel, there should be a label on the panel door. It will list all of the breakers approved for use in that panel. If you don't see the breaker by manufacturer name listed, then it should not be used. Lots of brands will interchange, but they have to be listed to be approved.
What on the periodic table metals are listed on the?
On the periodic table metals are listed on the left side.
How did Jupiter get the nicknames listed?
i dont know what u mean by listed but they were named by romans i think
How much watts does a normal vaccine fridge use?
Check the nameplate on the fridge. If the wattage in not listed look for the voltage and amperage that is listed. The formula for wattage is amps times volts. This will give you the answer that you are looking for.
What is the best site for drawing tutorials?
Please see the links listed below.
How do you Recover from a System Failure in GstarCAD?
A hardware problem, power failure, or software problem can cause this program to terminate unexpectedly. If this happens, you can restore the drawing files that were open.If the program fails, you can save your current work to a different file. This file uses the format, DrawingFileName_recover.dwg, where DrawingFileName is the file name of your current drawing.Resolve Drawing FilesAfter a program or system failure, the Drawing Recovery Manager opens the next time you start GstarCAD. Drawing Recovery Manager displays a list of all drawing files that were open, including the following drawing file types:Drawing files (DWG)Drawing template files (DWT)Drawing Standards files (DWS)For each drawing, you can open and choose from the following files if they existBackName_recover.dwgBackName_a_b_nnnn.sv$BackName.dwgBackName.bakNote:The drawing, backup, and recover files are listed in the order of their time stamps-the time when they were last saved.
What is Ratio between starting and running current of 3 phase ac motor?
The start up current should be listed on the motor nameplate as FLA , full load amps.
What is a good site that shows how to draw a Labrador using step-by-step drawing?
One is listed on the link below:
How can these problem be overcome by using SI unit?
What problem is being discussed? There is no problem listed in the question so it is difficult to provide an accurate answer.
What is the difference between spec control drawing and source control drawings?
Specification control drawing: Per MIL-STD-100, a drawing prepared for the purpose of defining and controlling screening, electrical performance characteristics, and physical configuration of purchased material. By definition, the intent of a Source Control Drawing is to purchase controlled standard parts.Source control drawing: Similar to a specification control drawing except that purchase of the specified devices from manufacturing sources other than those listed on the drawing is prohibited.
What is the cable size for 7.5kw slit system air conditioner?
The wire is sized to the maximum overcurrent protection device (Max circuit breaker) ampacity. This is listed on the nameplate of the outdoor condensing unit. Size the wire to match the breaker.
What is the transformation of a?
Impedance (Z) voltage is the amount of voltage applied to the primary side to produce full load current in the secondary side. It is usually listed on the transformer nameplate, expressed as a percent, and measured by conducting a short circuit test.
How these problems be overcome by using SI unit?
What problem is being discussed? There is no problem listed in the question so it is difficult to provide an accurate answer.
Why are emails listed as queued and not sent?
Emails can be listed as queued instead of sent if there is a problem with an email server. This basically means it is on hold and will be sent when everything clears.
Where is the low side port to recharge the AC located on a 2005 ford f150 5.4v8?
Its on the Receiver Drier/Accumulator. I found a drawing of it on the site listed below.
