0
no, 2 junctions. NPN or PNP
Wiki User
∙ 11y ago
Add your answer:
Earn +20 pts
What does 1n represents in 1n4007 transistor?
it represents one junction
Difference between bjt and ujt?
UJT is the voltage controlled device.in which only one mejority carriers are responsible for current flowing. UJT is one junction transistor and it is three terminal emitter and two base. BJT is the current controlled device. in which both mejority and minority carrier are responsiblefor current flowing. this type of transistor consists of two junction and three terminal these are : emitter , base , collector.
Why junction field effect transistor is called as unipolar devices?
Field Effect Transistors (both JFET & MOSFET) are unipolar because they use only one type of current carrier (electrons in N-channel or holes in P-channel), unlike bipolar transistors (both junction & the obsolete point contact) which always use both types of current carriers.
How must the two transistor junction be biased proper transistor amplifier operation?
A: Actually it is only one transistor required for amplification the other junction can be a diode. As current Begin to flow it causes a bias across one junction which is opposite biasing for the other, A good differential amplifier will have those junction virtually at the same point with a very good current source because any mismatched will cause and output without any input. It is called voltage offset on the other end if the feedback current is very small it will also produce an output voltage offset known as current offset or basically errors
What is the application of TTL in integrated circuits?
Transistor transistor logic is one type of many different types of bipolar transistor based digital logic circuitry. It is very efficiently implemented in integrated circuit chips, needs only one power supply voltage, and operates at reasonably high speeds. Transistor transistor logic was first developed in the middle 1960s as a modification of the diode transistor logic, then in use in some digital logic integrated circuit chips but dating back to the earliest discrete bipolar transistor logic developed in the late 1950s and derived from vacuum tube point contact diode logic used in many early first generation computers. Transistor transistor logic integrated circuits dominated the computer and electronic digital controller market from the late 1960s until the middle 1980s, when metal oxide semiconductor field effect transistor based microprocessors and microcontrollers began to replace it. By the early 1990s transistor transistor logic and other bipolar transistor based digital logic integrated circuits had been replaced with equivalent complementary metal oxide semiconductor field effect transistor integrated circuits that were both faster and consumed less power (thus running much cooler) or with programmable logic devices of various types. In general transistor transistor logic is now considered obsolete.
Can fet be used as a transisitors?
No. The Field Effect Transistor is a different technology than the Bipolar Junction Transistor. That cannot substitute for one another.
How can the bipolar junction transistor be used as a diode?
A: Yes it can but why ? This is frequently done when the diode is used for biasing purposes on another transistor and must be matched identically to the transistor's E-B junction characteristics. Thus 2 matched transistors are used with one just being used as a diode.
Can UJT replace BJT?
No. A unijunction transistor (UJT) is entirely different in design and application than a bipolar junction transistor (BJT). The UJT works on the principle of voltage modulation of the effective substrate resistance, while the BJT works on the principle of current amplification from one junction to the other, usually base-emitter to collector-emitter.
How a transistor use as a switch?
A transistor (bipolar junction transistor BJT) will only conduct in ONE DIRECTION. And the voltage drop is not Ohmic - it is *NOT* strictly related to current flow. If you're referring to a Field-Effect Transitor (JFET, IGFET, MOSFET, etc), then the device may be able to be used in a bidirectional circuit. But the question stated "transistor", which is understood to be a BJT.
How is a transistor used as a switch?
A transistor (bipolar junction transistor BJT) will only conduct in ONE DIRECTION. And the voltage drop is not Ohmic - it is *NOT* strictly related to current flow. If you're referring to a Field-Effect Transitor (JFET, IGFET, MOSFET, etc), then the device may be able to be used in a bidirectional circuit. But the question stated "transistor", which is understood to be a BJT.
What does 1n represents in 1n4007 transistor?
it represents one junction
Difference between bjt and ujt?
UJT is the voltage controlled device.in which only one mejority carriers are responsible for current flowing. UJT is one junction transistor and it is three terminal emitter and two base. BJT is the current controlled device. in which both mejority and minority carrier are responsiblefor current flowing. this type of transistor consists of two junction and three terminal these are : emitter , base , collector.
What is the difference between the UJT and BJT transistors?
UJT (UniJunction Transistor): It is a transistor with only one junction and three terminals: an emitter (E) and two bases (B1 and B2). BJT (Bipolar Junction Transistor): This type of transistor consists of two junctions and three terminals, namely Emitter "E", Base "B" and Collector"C". There are two types of BJT, i) PNP and ii) NPN.
Where did the first transistor computer come from?
bell labs built one out of early point contact transistors in 1948 before the invention of the junction transistor.
Why transistor is called transistor?
Because in this device the resistance between two terminal respectively collector and emitter is changed by changing the base voltage that is it transfers the resistance between emitter and collector therefore it is called as TRANSISTOR. (TRANSFER OF RESISTOR)
What is the application of bipolar junction transister?
bipolar junction transistor is known as BJT in short form.they are made by cascading two P-N junction.we can not imagine any electronics circuit without Bjt.they have plenty of applications,one of the most important application is of switch.it can act as a switch.moreover it can act as a resistor.they can amplify weak signals into strong signals.in a chip which is used to run a computer or laptop there are millions of transistors cascaded in a chip which has size nearly of fingernail. you can find more information on youtubeBy-Nihar.N.Suryawanshi.
Can you use transistor as a rectifier?
No, a Transistor operates with a modulated direct current. You need 4 Diodes to manufacture a rectifier to deliver direct current at the outlet, with alternating current at the input. A Diode is effectively a one way valve to address one halve of the cycle of the alternating current.
