0
Is it acceptable to position a printer under or close to a window?
Cymjsm
Preferably not, as outside dust and humidity will be higher from an opening, which can cause malfunction and shorting in delicate connections in electrical devices.
Wiki User
∙ 14y ago
Add your answer:
Earn +20 pts
When locking the doors on 2001 VW Polo the electric windows open instead?
if you hold the key in the lock position it will close the window also held in the open position it will open the window
How do you reset window relay on a Vauxhall Frontera?
Close the window press the button again as if to close and listen for a click window reset
Which position is above or close to the head?
Anatomical position is a position which is above or close to the head.
How do you close a window on a mac book?
press the red button at the top left corner of the window. or just press command+w and the window will close
How do you write javascript code to close a browser window?
If you want to close the current window, use window.close() or simply close() If you want to close a window that is stored in a JavaScript variable, apply the method close() to it. For example: var myWindow=window.open("http:\/\/www.example.com/"); myWindow.close();
Which tab in the Format Legend window would you select if you wanted to change the position of the chart's legend?
Excel 2007:Click on chart.Right-click on ledgend and select Format Legend.In Legend Options, slect the position for the legend (top, bottom, left, right, or top right).Close Format Legend window.
What key do you press to close the window on the sims 3 motherlode?
To close the window just press Escape on your keyboard (ESC).
How do get rid of nats by your window?
Close it.
How do you close an open window from the Task Bar?
TRY Clicking the red X button on the window. Bamm! works like a miracle.
How do you reset windows on a 1996 range rover i am getting a readint that says windows not set?
Answer:What you need to do is open each window and then close them one at a time, holding the switch in the up position until the display reads "window set". Open the sunroof fully then close it and press the switch again to open it to the vent position. This will reset the sunroof.If the display continues to show "window not set" just lower it fully and then raise it again holding the switch when it gets to the top. Sometimes it takes 2 or 3 tries.
Is it acceptable to tell close friends you're engaged on Facebook?
No
How do you initialize the rear window motor on a 2001 ford sport trac?
Rear Window Motor InitializationWhen you install the new motor, it MUST BE "INITIALIZED" before it will function properly. Simply follow the instructions below. CAUTION: Make sure that no obstructions are present in the power rear window system when carrying out this procedure.NOTE: The rear window motor is in error mode when shipped and will be inoperative until initialized.NOTE: This procedure must be carried out when repairs are performed on any part of the power rear window system including when: the power rear window motor is removed from the window regulator drum housing, a new power rear motor is installed, a new power rear window regulator is installed, a new power rear window glass module is installed, and any operation in which grease or lubricants are applied to the power rear window system.NOTE: All power rear window components (window glass module, window regulator, window motor, and glass runs) must be installed and torqued to specification before carrying out this procedure.NOTE: Once the ignition key is turned to the ON position in Step 6, it must remain on until the entire procedure is completed.NOTE: Step 7 requires that the power rear window control switch be held in the CLOSE position (fully clockwise) until the power rear window motor stalls the window into the upper header seal. Step 8 requires that the window control switch be momentarily turned to the OPEN position.NOTE: Step 9 requires that the power rear window control switch be held in the CLOSE position (fully clockwise) until the window stalls into the upper header seal and the window carries out its down-up sequence, indicating successful completion of initialization.NOTE: The key-in-ignition chime can cause the vent button to be pressed more or less than six times due to the distraction of the chime.NOTE: Steps 1-6 must be completed within 30 seconds. The entire procedure must be completed within five minutes.Start with the ignition in the OFF position. Open the driver door.Turn the ignition to the ON position.Press the power rear window control switch vent button six times.Turn the ignition to the OFF position. The driver door must be OPEN.Press the power rear window control switch vent button six times.Turn the ignition to the ON position. The power rear window will move down-up-down-up approximately 20 mm (0.8 in). This movement indicates that the power rear window motor has entered initialization mode.Rotate and hold the power rear window control switch to the CLOSE position until the window stalls into the upper header seal.Momentarily rotate the power rear window control switch to the OPEN position and release. The power rear window will carry out a one-touch down operation until the window stalls at the bottom of the travel stop designed into the window regulator.Rotate and hold the power rear window control switch to the CLOSE position. Continue to hold the switch until after the window stalls into the upper header seal and carries out the down-up movement. This down-up movement is approximately 20 mm (0.8 in). This movement indicates that the power rear window motor has been successfully initialized.Verify correct operation of the power rear window by moving the window to the fully open, vent, then fully closed positions. If the window does not operate correctly, carefully repeat this procedure.NOTE. You will need to close the door after step 6.
