0
Is it necessary for 2 diodes of full wave rectifier to be identical?
Wiki User
∙ 14y ago
It is not really necessary for 2 diodes of full wave rectifier to be identical.
However, it must be understood that the two diodes will have the same forward current, and the same reverse voltage, applied to them, so their ratings should be comparable.
Wiki User
∙ 14y ago
Add your answer:
Earn +20 pts
Can you make transistor with 2 diode?
Yes, if the transformer output is center-tapped; otherwise, no, a bridge rectifier requires four diodes, or six for three phase power. More technically correct, what we are talking about is a full-wave rectifier. A bridge rectifier is properly always four or six diodes.
Why bridge rectifier is prefer over center type rectifier for low voltage applications?
there is no need of bulky centre tap in a bridge rectifier. TUF(transformer utilisation factor) is considerably high. output is not grounded. diodes of a bridge rectifier are readily available in market. *the PIV(peak inverse voltage) for diodes in a bridge rectifier are only halfof that for a centre tapped full wave rectifier,which is of great advantage.
What are the advantages and dis advantage of full-wave bridge rectifier compared with two diodes rectifier?
in full wave bridge rectifier, the input and out put voltages are same but in case of two diode rectifier the input and output voltages can be different as per requirement a there is a transformer in the circuit. The former is lighter and the later is heavier.
What is the basic difference between a full wave bridge rectifier and a full wave center tapped rectifier?
A full-wave bridge rectifier with 4 diodes gives a dc output voltage equal to the average voltage of the whole transformer secondary. A FW rectifier with 2 diodes and a centre-tapped secondary gives an output voltage equal to the average voltage of half the secondary. If you have a 12-0-12 transformer, the bridge gives a 24 v output, while the 2-diode FW rectifier gives 12 v (approximately).
How many diodes are used to make a half wave rectifier?
You use a half-wave rectifier where the system design does not require a full-wave approach. Half wave rectifier output is used for running ac motors.
How many diodes in a bridge rectifier?
Bridge Rectifier DiodesIn a "bridge" rectifier there is 4 diodes In a "full wave" there are 2 diodes.In a "half wave" rectifier there is 1 diode.
What has the greater current in the diodes bridge rectifier circuit or full-wave rectifier circuit?
They both have the same current.
A full wave bridge rectifier uses how many diodes?
to flow the electrons one way
How many diodes in full wave rectifier?
Depends on the number of phases.single phase uses 4 diodesthree phase uses 6 diodes
Difference between 4 diodes and 2 diodes rectifier?
a 2 diode rectifier is a center tap rectifier an a 4 diode rectifier will be a bridge rectifier *********************************************************** A two-diode rectifier is not always a centre-tap rectifier. If the two diodes are connected to the same end of a transformer's secondary, one by its anode and one by its cathode, one will proved a positive voltage with respect to trhe other end of the winding and the other will provide a negative voltage. (But perhaps that isn't considered a two-diode rectifier - but a two single-diode ones.)
Is 2 diode without center taped can befull wave rectifier?
No. For a full wave rectifier, you need two diodes and a center tapped secondary, or you need four diodes and a non-center tapped secondary.
Can you make transistor with 2 diode?
Yes, if the transformer output is center-tapped; otherwise, no, a bridge rectifier requires four diodes, or six for three phase power. More technically correct, what we are talking about is a full-wave rectifier. A bridge rectifier is properly always four or six diodes.
How convert 3 -phases ac into dc?
Use a full wave rectifier with 6 diodes, as in a car alternator.
What should be the PIV rating of the diodes in the full wave rectifire?
A: The same as a half wave rectifier RMS x1.41
Full wave rectifier using RC triggering circuit with diagram?
A full-wave rectifier (sometimes called a "bridge" rectifier) produces output current on both half-cycles of the input AC waveform. ******************************************** There are two types of full wave rectifier circuit. One uses four diodes in a "bridge"configuration and is fed from a simple transformer winding. The other uses two diodes and needs to be fed from a centre tapped transformer winding.
Why bridge rectifier is prefer over center type rectifier for low voltage applications?
there is no need of bulky centre tap in a bridge rectifier. TUF(transformer utilisation factor) is considerably high. output is not grounded. diodes of a bridge rectifier are readily available in market. *the PIV(peak inverse voltage) for diodes in a bridge rectifier are only halfof that for a centre tapped full wave rectifier,which is of great advantage.
What is the main difference between a bridge rectifier and a full wave rectifier?
Both the bridge rectifier and the full-wave rectifier achieve the same thing. They rectify the AC input on both opposing phases so as to minimize ripple time and voltage. The difference is that a bridge rectifier consists of four diodes arranged in a bridge, so the input needs to only be single phase AC, while a full wave rectifier consists of two diodes, but needs a split phase AC source, such as provided by a center tapped transformer winding. Also, the bridge rectifier presents two junction drops in the output, because there are always two diodes in series, while the full-wave rectifier presents only one junction drop in the output, because there is only one. It is a trade-off.
