Yes. the two switches are called '3-way' switches. You will have to turn the fan/light on with one of the switches and leave BOTH switches in that position. The remote control unit will have to be wired in between the switch that is supplying power to the devices and the devices. This is the simplest way.
You could also disable one of the switches and replace the remaining switch with the RC unit. If you are not sure how to deal with 3-way switches, learn about them first, or call a good electrician to do all of the work. Remeber that the black wire is hot, but only if the house was wired properly in the first place.
Yes, in fact my ceiling fan and light are controlled by remote control, mine is made by designe control (DC)
A photocontrol uses light to activate the switch. When the sensor does not detect light the circuit is broken and the switch is deactivated.
There are many places where one could buy a timer to control a light switch. One looking for a timer to control a light switch should visit popular on the web sources such as Lowe's, Intermatic, and Honeywell Store.
The fan is wired to the house wrong. Typically the red switch wire in the ceiling box will be nutted off and not used when a remote is installed. Sounds like, in this case, the fan light wire (blue) was connected to the red switch wire in the ceiling box instead of being correctly connected to the remote unit at the fan.
Not usually, The light would have had to been wired with a three wire from the switch to the fan. One circuit to control the fan and the other switch to control the light. If this is your situation then all you will have to do is change the light switch to a timer and that will do what you want.
Some brand fans have a remote control kit that installs in the fan housing. Also if you have access you can run a separate switched voltage to the fan. In this case you would have to put a second switch in the same box that controls fan, unless it is a switch with speed control that came with fan. In this case you would have to install a new box (Old Work Switch Box from Home Depot or Lowes for example) and run voltage to the box, install a switch and run wire to fan and connect to light. One other possibility is to check the ceiling box and see if there is a spare red wire. If so you could use this to switch power to the light separately from the fan. Again it depends on the switch configuration and supply voltage feed.
A remote light switch is a switch that triggers a light by remote. You can get one installed through your local home department store and have it rigged up to a universal remote.
When installing a remote light switch one must first turn the power off. This will prevent shock or electrocution. Next, unscrew the plate currently on the wall and remove the switch and wire the new one with remote. Next remove the light from the ceiling and install the remote sensor. Place light cover back over light and turn power back on. Program and test remote control to ensure wiring was correctly installed.
with light switch off, hold the "off" button on the fan part of the control & then turn light switch on while still holding the button.
If you have two switches connected to a light in a room.example your bed room and you are in your bed you wont have to get out of your bed to switch off the light but u can switch it off by pulling a switch over your head.
the television has a switch that makes possible for it to light on an off, the remote control has a malty sensor that allow sensory waves to be detected in an immediate effect when pressing some of the buttons on the remote control, co ordination is carried by eclectic waves that allow stimuli as electrons pass through conductors allowing a electric flow of current.
To control a light with a switch, the switch has to be connected in series with the light fixture.
Supposing you have a remote to control the light, the remote for the light and the remote for the TV are probably on the same frequency.
In this remote, the little LED light that controls the remote will emit the infra red spectrum. You will not see the light but the control will work.
This system does not include a remote control device.
"A remote light switch is made by an electrical company, as that is one of the new trends in society today. Just go to a local hardware store and you'll find many options."
Electrical equipment usually comes with its own instructions, so search the box in which it arrived. If that's not an option, eHow has an article titled "How to Install a Remote Light Switch."
A photocontrol uses light to activate the switch. When the sensor does not detect light the circuit is broken and the switch is deactivated.