0
Absolutely! There are many ways of doing this depending on what you want the switches to do.
This is referred to as looping. (One would loop the hot wire to the next switch)
For instance, take the downstairs of a house. you would take a hot wire from the board, bring it to the switch in the hall, from the same connection on that switch (let's say the top connection), you bring a loop to the top of the lounge switch, and on again to the top of the kitchen switch. Now you wire from the bottom of each switch to the respective light(s)
in each room. and bring a neutral wire back from the lights to the board. Make sure not to forget to bring an earth wire to the switches and the lights. Presto: lighting circuit complete.
There are other ways of looping the hot. For example you have a switch at the top and bottom of your staircase that controls the same lights. This is a little more complicated to explain though.
So the answer is yes, it is perfectly fine to jump a hot wire to a second switch.
What else can I help you with?
How to wire 2 lights to one switch?
To wire two lights to one switch, you will need to connect the power source to the switch, then run a wire from the switch to the first light, and another wire from the first light to the second light. Make sure to follow proper safety precautions and consult a professional if needed.
How can you wire a 3-way switch using only 12-2 wire?
To wire a 3-way switch using only 12-2 wire, connect the black (hot) wire from the power source to the common terminal of the first switch. Then, run a 12-2 cable to the second switch, connecting the two traveler terminals of the first switch to the two traveler terminals of the second switch using the black and red wires. Finally, connect the common terminal of the second switch to the light fixture, and ensure the white wire is properly connected as a neutral back to the fixture. Remember to use wire nuts and ensure proper grounding.
How to wire two lights to one switch?
To wire two lights to one switch, you will need to connect the power source to the switch, then run a wire from the switch to the first light, and another wire from the first light to the second light. This creates a series circuit where both lights are controlled by the same switch. Make sure to follow proper safety precautions and consult a professional if needed.
How can I jump power from one light switch to another?
To jump power from one light switch to another, you can connect a wire from the hot terminal of the first switch to the hot terminal of the second switch. Make sure to turn off the power before attempting any electrical work and consult a professional if you are unsure.
What is the proper wiring diagram for a Lutron dimmer switch?
The proper wiring diagram for a Lutron dimmer switch typically involves connecting the hot wire to the black wire, the neutral wire to the white wire, and the load wire to the red wire. It's important to follow the specific instructions provided by Lutron for your dimmer switch model to ensure proper installation and functionality.
How do you properly wire a 2 switch light switch configuration?
To properly wire a 2 switch light switch configuration, you will need to connect the power source to the common terminal of the first switch. Then, connect the travelers from the first switch to the corresponding terminals on the second switch. Finally, connect the light fixture to the common terminal of the second switch. Make sure to follow the specific wiring diagram for your setup to ensure proper installation.
What is a proper way to connect a second starter wire?
The proper way to connect a second starter wire depends with the configuration used.
What is the 4-wire ceiling fan switch wiring diagram for proper installation and operation?
The 4-wire ceiling fan switch wiring diagram includes connecting the black wire to the fan's hot wire, the blue wire to the light kit's hot wire, the white wire to the neutral wire, and the green wire to the ground wire for proper installation and operation.
How can I wire 2 lights with 2 switches in a single circuit?
To wire 2 lights with 2 switches in a single circuit, you will need to connect the power source to the first switch, then run a wire from that switch to the first light. From the first light, run another wire to the second light. Finally, connect a wire from the second light to the second switch. This setup allows you to control each light independently with its respective switch.
How can I wire a 3-way switch diagram with power at the switch?
To wire a 3-way switch diagram with power at the switch, you will need to connect the power source to the common terminal of the first switch. Then, connect the travelers between the two switches and the load to the common terminal of the second switch. Make sure to follow the specific wiring diagram for your setup to ensure proper installation.
What is a red wire switch leg?
A red wire switch leg is a specific wire used in electrical wiring to connect a switch to a light fixture or another electrical device. The red wire serves as the hot wire that carries electricity to the switch, allowing it to control the flow of electricity to the connected device. It is essential to follow proper electrical codes and guidelines when working with red wire switch legs to ensure safety and proper functionality.
How do you know which switch to change if there are 3 switches on a cooling fan control circuit relay?
take a wire and jump each switch
