0
This is an interesting question. I will assume you refer to bus bars - as a separate component - that connect two pieces of equipment, and not as an integral componet of a device such as a switch. "Maintenance" can mean whatever a person wants it to mean.
"Required" is almost equally vague. Maintenance could include testing, inspecting, cleaning, repairing, tightening, measuring (temperature-amperage) or all the above. "Required" generally means required by the Authority Having Jurisdiction (AHJ) - That could be any number of people: the local code enforement agency, an insurance company, utility company, the owner, or the manufacturer or a combination of them. Some insurers require the main service components of a building to be shutdown once every year or so and have all the joints torque wrench tightened. This would include bus-bar joints. Some require thermoscans to find hot stops. Some utility companies require the bus to be meggar tested before re-energizing, even if for a ten minute outage. I do not believe the NFPA electrical standard has any particular requirements for bus bar maintenance, however they always state "follow the manufacturer's recommendations". From a practical point of view the bars themselves do not degrade, but the joints can give trouble occassionally. The insulation around or supporting the bars can degrade and cause trouble. Thermoscanning is a nice inexpensive way to keep an eye on developing problems.
Wiki User
∙ 16y ago
Add your answer:
Earn +20 pts
What tests need to be carried out when commissioning bus bars?
Bus bars need to be meggered to make sure that there is no shorts between the bars and from the bars to ground. Usually electrical engineers have a list that has to be checked off and values written down before any energizing of the equipment will be allowed.
What are service panel bus bars?
Typically copper conductors that provide a phase of electricity.
What is Bus bar electrical?
A bus bar is a solid copper or aluminium bar that is used in switch gear and motor control centers. Smaller bus bars are used in central distribution panels and seen in everyday use, the bars that the household breakers plug or bolt into in a homes distribution panel. The bars in switch gear and MCC's are rated to carry a rated current. To bend a wire into the back of these types of equipment would be next to impossible due to the constraints of limited space.Additional InformationThe word 'busbar' is derived from the word, 'omnibus', meaning to 'serve all', which is exactly what a busbar does -it serves all the circuits connected to it.Occasionally, you see the word, 'busbar', spelt as 'bussbar' -this is an incorrect spelling which indicates a lack of knowledge of the origin of the word.
Why pt coil is not present in three phase watt meter?
A three phase watt meter's potential transformer and current transformer are located remotely from the metering cabinet. On large size bus installations it would be impossible to take the bus bars to the meter so it is done the other way around. Leave the Ct's and Pt's on the bus bars and use smaller wire to feed the meter in a remote accessible location. The utility company requires a metering cabinet over certain voltages and amperage be accessible to the meter reader. In some installations the metering cabinet is installed remotely on the outside of the building away from the electrical room.
What is a bus on a electrical distribution system?
a path through which power is transferred from generating station to consumers.
What type of electrical equipment uses bus bars in its construction?
High current service entrance equipment and MCC (motor control centers) all use bus bars in their construction.
What tests need to be carried out when commissioning bus bars?
Bus bars need to be meggered to make sure that there is no shorts between the bars and from the bars to ground. Usually electrical engineers have a list that has to be checked off and values written down before any energizing of the equipment will be allowed.
Where is a Bus bar in a circuit?
Where there is an electrical connection required from one feeder to many feeder , then you need a reference or grid from where the loads can be distributed.
What is a stab in an electrical panel?
A stab is a way of connecting an external electrical device to a distribution bus bar. Stab lok breakers have a stab that connects the breaker to the bus bar by pushing the breaker into the bus bar and the breaker stab applies pressure in four directions to secure it. Another device that uses a stab is a module (bucket) that fits into a MCC (motor control center). These stabs are movable and are used to align the module to the bus bars. Using stabs on these devices allows for expansion and contraction of the bus bars when heavy loading generates heat. Also individual modules can be removed from the MCC without shutting the entire MCC off.
What companies sell a bus duct?
There are many companies that sell a bus duct. Examples of companies that sell a bus duct include South Land Electrical, Sailing Electrical, and BD Electrical.
What is the difference between a 100 amp breaker box and a 125 breaker box?
The amperage capacity of the main bus bars and the connection of the main breaker to the bus bars.
What are bus lines job in computer internal component?
Buses in the computer exist to carry signals between electrical devices. They are called that because the number of traces that close resemble bus bars in an old telephone relay. There are different bus technologies. Some are parallel, and some are serial and perhaps even compressed.
Do you have to wear a seatbelt on a bus?
If the bus has seatbelts on it (for ex. a charter bus) then yes, you are required to wear a seatbelt. If you are referring to a school bus, then no, seatbelts are not required.
Is the normal voltage of house electricity in the US AC?
Yes. It is 60 Hz between 110 and 120 volts on each of two bus bars with 220 to 240 volts between two bus bars.
Difference between bus bar and bus duct?
Bus bars are actually simple conductor strips of copper using for connection between one system to another.for example transformer to panel. bus ducts are enclouser of that bus bar
What are the conditions in parallel operation of generator?
the operation of connecting an alternator with other alternator or with common bus-bars is known as synchronizing.Generally alternator used in power system where they are connected in parallel with other alternator.condition for parallel operation of an alternator1. The terminal voltage of incoming alternator must be same as the bus-bars voltage.2. The speed of incoming alternator must be such that its frequency f =pn/120 as the same frequency of the bus-bars.3. The voltage of incoming alternator and the bus-bars voltage are in same phage.
What are service panel bus bars?
Typically copper conductors that provide a phase of electricity.
