0
Want this question answered?
Be notified when an answer is posted
Add your answer:
Earn +20 pts
Why cant take connection from phase line to neutral line?
A connection can be taken between phase lines, or between one phase and neutral. Both methods give a single-phase supply. Between phases the voltage is sqrt(3) times more than between one phase and neutral. In each case the load gives an unbalanced current on the 3-phase system but the idea is to average out the unbalances over a group of single-phase loads.
If in the three phase connection phase to phase voltage is 400v what will be the phase neutral voltage?
The formula to use is, phase voltage /1.73 = phase to neutral (ground) voltage.CommentThere is no such thing as a 'phase to phase', or 'phase to neutral' voltage. The correct terms are 'line to line' and 'line to neutral'. So the above answer should read: line voltage/1.73= line to neutral voltage = phase voltage.
Can delta connection be used on 3 phase 4 wire system?
A delta connected appliance can be connected to a 3-phase system by leaving the neutral unconnected. The appliance must be properly earthed.
How can you terminate a 3 wire wye motor to a 3 phase delta connection?
To terminate a 3 wire wye motor to a 3 phase delta connection you need a 3 phase transformer to convert from delta to wye. Do not lift the common neutral connections inside the motor and rewire for delta, because the voltages will be wrong.
How three phase line current convert in single phase?
The current is the same in the three live wires. The voltage can be described as the line voltage (phase to neutral) or the phase voltage (phase to phase) which is larger by a factor of sqrt(3). So a line voltage of 230 v corresponds to a phase voltage of 400 v.
Why cant take connection from phase line to neutral line?
A connection can be taken between phase lines, or between one phase and neutral. Both methods give a single-phase supply. Between phases the voltage is sqrt(3) times more than between one phase and neutral. In each case the load gives an unbalanced current on the 3-phase system but the idea is to average out the unbalances over a group of single-phase loads.
If in the three phase connection phase to phase voltage is 400v what will be the phase neutral voltage?
The formula to use is, phase voltage /1.73 = phase to neutral (ground) voltage.CommentThere is no such thing as a 'phase to phase', or 'phase to neutral' voltage. The correct terms are 'line to line' and 'line to neutral'. So the above answer should read: line voltage/1.73= line to neutral voltage = phase voltage.
Can delta connection be used on 3 phase 4 wire system?
A delta connected appliance can be connected to a 3-phase system by leaving the neutral unconnected. The appliance must be properly earthed.
How can you terminate a 3 wire wye motor to a 3 phase delta connection?
To terminate a 3 wire wye motor to a 3 phase delta connection you need a 3 phase transformer to convert from delta to wye. Do not lift the common neutral connections inside the motor and rewire for delta, because the voltages will be wrong.
What is the code ruling in the US on 3 phase branch circuits and the neutral?
A three phase system will have 3 phase branch circuits and no neutral.
Why is it stated - 3 phase 440 VAC when one phase voltage is 220 VAC?
In three-phase there are three live wires and a neutral. The voltage of a three-phase system is always quoted as the live-to-live voltage, and the voltage from one live wire to neutral is 57.7% of that. A 440 v 3-ph system has 254 volts between live and neutral. <<>> The question statement is not correct. Two legs from a three phase three wire 440 volt system will still be 440 but classed a single phase. On a three phase four wire system supply, the voltages will be determined by the following equation. 440/(square root of 3) 1.73 = 254 volts. The second single phase voltage attainable from this source connection is any one of the three phase legs to grounded neutral center point. This is known as a wye or star point connected voltage supply. To obtain a 220 volt single phase voltage, the three phase system would have to have a voltage of 220 x 1.73 = 380 volts.
How three phase line current convert in single phase?
The current is the same in the three live wires. The voltage can be described as the line voltage (phase to neutral) or the phase voltage (phase to phase) which is larger by a factor of sqrt(3). So a line voltage of 230 v corresponds to a phase voltage of 400 v.
Why neutral is not requied in 3 phase?
As far as I understand, you don't need neutral line for connecting appliances that is 3-phase compilant. You only need the neutral line to connect a single phase appliance, which you connect along with one of the three lines.
What is the voltage for each leg on a 480v 3-phase pannel phase to neutral?
Only one neutral conductor is typically in a 3 phase panel.
How do you create a common lead from 3 phase 120 volt?
If you are referring a common lead as meaning a neutral of a three phase system, the three phase voltage has to be 208 volts. This type of connection is in a wye configuration. It is found by this formula 208/1.73 = 120 volts. This connection will supply 120 volts between any one of the three supply legs and the grounded neutral.
Do you need a neutral to install 480 volts 3 phase heater?
If the heater is rated as a 3 phase 480 volt heater then a neutral is not needed. If the voltage stated is 277 volts three phase then a neutral is needed.
How many wire or core in three phase electrical connection and single-phase electrical connection?
A single-phase cable will have a line and a neutral conductor and, possibly, but not necessarily, an earth (ground) conductor. A high-voltage three-phase cable will have three line conductors. A low-voltage three-phase cable is likely to have three line conductors and a neutral conductor.
