0
Is the hood hinge the thing that connects the hood to the fender?
Wiki User
∙ 14y ago
Yes, the hood hinges bolt to the hood and then go down and bolt underneath of the cowl that runs across the front of the engine compartment.
Wiki User
∙ 14y ago
Add your answer:
Earn +20 pts
Where is the single wire in line spout connector on 93 f150?
Drivers side fender well by the hood hinge
How do you replace left hood hinge on dodge ram 2500?
Raise the hood and support it in the center with a stick between the lock and radiator support. The opposite hinge will keep the hood up, for the most part. Have a folded towel or blanket to protect the fender and windshield from the rear corner of the hood. Remove the 2 nuts holding the hood to the hinge. Lift the hood corner to free the studs from the hinge, keeping control of the hood to rest it on the blanket. Now you can remove the 3 bolts holding the hinge to the body. Two bolts on the top of the hinge are accessible from the outside; the third, bottom bolt is accessed from the engine compartment. Reverse procedure to install the new hinge.
If you have a 1978 mercury marquis and need a hood hinge can you use a Ford or Lincoln hood hinge?
hinge hood merqury gran marquis 1978
How muscles and bone work together?
by the other parts
How do you open the hood when the hood latch release is pulled on a 1996 Nissan pickup and it does not open?
I just bought a `96 and it had the same problem. I fixed it. Close the hood until it is almost latched. Observe whether one side of the hood is closer to a fender than the other side. If one side of the hood is closer to a fender, then the hood will also be closer at the back edge (near the firewall) than the opposite back edge. You need to adjust the hood forward at that hinge. If there is still putty around hinge/hood mating surfaces, chisel it off with a small screwdriver. Loosen the two 10mm hinge bolts slightly (about 1/8 inch). Break the hood loose from the hinge by prying. This will allow you to reposition that side of the hood. Move the hood upward/forward at that hinge (about 1/16 inch) and tighten one of the bolts. Close the hood and see if the back corners are about an equal distance from the firewall. Equalize the left and right back edges of the hood fairly closely. Oil the latch mechanism. I had to also adjust the latch itself, so that the hood closed tighter. To adjust the latch, you loosen the three 12mm bolts. Good Luck !
Where is the jack stored on a ford e350?
Most pickup jacks are either stored, Behind Seat, In Compartment behind Seat, OR under the hood on one of the fender wheels, (usually passenger side, Close to the hood Hinge) Depending on year
How do you remove right front fender on 2003 civic?
The right front fender on the 2003 Honda Civic is held on by several mounting bolts and screws. Raise the hood and loosen the bolts. Raise the vehicle and remove the wheel to reach the bolts in the wheel weld. Remove the bolts inside the door hinge and the screws on the bumper. Remove the fender.
How does one replace a 1989 Chevy Suburban left front fender?
Open the hood, Un bolt the hood hinge,mark the bolt holes to insure propper alignment later, Support the hood ,Locate all the inner Fender bolts along the inside well of the truck, unbolt them, 1/2 or 9/16ths socket, open the drivers door, unbolt the fender bolts there, remove the lfet side section of the front grille, if one piece remove the whole grille, check for bolts in the grille area, remove the fender, reverse procedure to re-install, aligne the bolt holes and check the hood line gap with the passenger side, make sure the fender does not rub on the door when you close it, adjust as necessary.. tighten all bolts...Open the hood, Un bolt the hood hinge,mark the bolt holes to insure propper alignment later, Support the hood ,Locate all the inner Fender bolts along the inside well of the truck, unbolt them, 1/2 or 9/16ths socket, open the drivers door, unbolt the fender bolts there, remove the lfet side section of the front grille, if one piece remove the whole grille, check for bolts in the grille area, remove the fender, reverse procedure to re-install, aligne the bolt holes and check the hood line gap with the passenger side, make sure the fender does not rub on the door when you close it, adjust as necessary.. tighten all bolts...
How do you remove a fender on a 2000 Chevy Express van?
Open hood and remove all the bolts on the seam (including the prop rod). One bolt will be in the space between the grille and the bumper. Remove the bolt holding the hood hinge. Put a flat screw driver or flat chisel between the two pieces of metal held together with a rivet and gently pry (there are two, and they are located between the door and fender). You do not neeed to remove the fender liner.
Where is the Obd1 hookup on a 1990 Volvo 240 dl?
Under the hood by the left hood hinge.
Where is the diagnostic port on a 1992 ford bronco?
under the hood on the drivers side by the hood hinge
Where is diagnostic port on 1992 F-150?
under the hood on the drivers side by the hood hinge
