Want this question answered?
half coupling used to take branch from header ie: 2" header to 3/4' branch. where full coupling used to connect to straight pipe. ie: 2" to 2" pipe connection.
It can be one step down in size, 3/4 to 1/2 or a larger jump, 4 inch to 2 inch. Depends on the location and what you are wanting to do.
It is tricky but u can with a fernco if the copper dwv drain line is 1 1/2" in diamater use a 1 1/4" x 1 1/2" reducing fernco because the outside diamater of copper is smaller than abs or PVC
You can put up to a 2 inch pipe into a 4 inch. If you are putting 4 inch to 4 inch, either take out a section of the cast and put the PVC in or cut out a section and connect the PVC to the cast with rubber sleeves meant for this. You can use a saddle clamp for the 2 inch. It is a half round piece of PVC with a 2 inch connection in it. It is held on with two U bolts that go around the cast pipe. Put it where you need it and mark the 2 inch hole on the cast. Drill a series of 1/8 inch holes around this circle. when you get them all drilled, you can break out the plug. Try to keep it from falling into the cast pipe. Put the saddle clamp on and connect the PVC pipe as needed. Seal the saddle clamp to the cast pipe with plumbers putty.
For sanitary and venting, 5 psi. for 15 minutes.
half coupling used to take branch from header ie: 2" header to 3/4' branch. where full coupling used to connect to straight pipe. ie: 2" to 2" pipe connection.
Electrical trade sizes of PVC conduit are, - 1/2" = 12.5mm, 3/4" = 19mm, 1" = 25mm, 1 1/4" = 32mm, 1 1/2" = 38mm, 2" = 50mm, 3" = 75mm, 4" = 100mm.
do you want that PVC in schedule 40 or schedule 80,1",2"? its a PCV-(Positive Crankcase ventilation )valve.
form_title= PVC Fittings form_header= Make DIY a snap with PVC fittings. How many fittings do you need?*= {1, 2, 3, 4, 5, 6, 7, 8, 9, 10, More than 10} What size PVC do you need?*= _ [50] What will you be using the PVC for?*= _ [50]
It is a fluid coupling using a viscous (thicker type) fluid, similar to the coupling between the drive and driven impeller of an automatic transmission in a car.
wool
6
the 4 materials made from thermo plastics:- 1.polythene bags 2.stationary 3.containers 4.PVC
Depends on the size of the conduit and the size of the wire.Allowable Conduit Fill CapacitiesSize and Type Of Conduit #14 Wire #12 Wire #10 Wire 1/2" EMT 12 9 5 3/4" EMT 22 16 10 1" EMT 35 26 16 1 1/2" EMT 84 61 38 1/2" PVC 10 7 4 3/4" PVC 18 13 8 1" PVC 32 23 15 1 1/2" PVC 80 58 36
200 amp underground service -200 amp meter6' long 2" PVC pipe2" connectorground plateground wire - depends on where you live6' long 1/4" PVC pipe1/4" connectorPVC glue3" PVC pipe for power coming in3" connectorsome 1/2 inch wood screwswire to run from the meter to the panel - depends on where you livetyveck
It can be one step down in size, 3/4 to 1/2 or a larger jump, 4 inch to 2 inch. Depends on the location and what you are wanting to do.
It is tricky but u can with a fernco if the copper dwv drain line is 1 1/2" in diamater use a 1 1/4" x 1 1/2" reducing fernco because the outside diamater of copper is smaller than abs or PVC