0
Anyone installing any lighting systems should be licensed and insured.
Wiki User
∙ 16y ago
Add your answer:
Earn +20 pts
What is the difference between line voltage and low voltage?
Answer for USA, Canada and countries running a 60 Hertz supply service.Line voltage is a term that is used to describe the voltage that is used to operate a specific device. A service that comes into a building would be considered line voltage. For a Class 1 circuit the top voltage for low voltage installations is 30 volts at 1000 vA. For a Class 2 circuit the top voltage for low voltage installations is not under 30 volts and not over 60 volts at 100 vA. Voltages used above 750 volts are considered high voltage installations.
How do i switch a 3 phase motor from low to high voltage?
You can't. You must supply the motor with it's required voltage. If it's a dual voltage motor, follow the wiring schematic on the motor nameplate to switch from low to high voltage.
Do you need a licenced electrician to hang conduit for low voltage cable?
In most places, for residential, no. For commercial, most jurisdictions require a contractors license for anyelectrical work. Where I live, there is a low-voltage license that is less than a full-blown electrical license that is used by fire alarm, security, and telecommunications contractors. The NEC and most jurisdictions define low voltage as less than 30 volts. Check with your local building department to be sure!
What is classed as high voltage in the UK?
>1000V rms ACAnswerAccording to BS 7671:2008 Requirements for Electrical Installations, 'high voltage' is formally defined as that 'normally exceeding low voltage', where 'low voltage' is defined as "...(nominal voltages) exceeding extra-low voltage but not exceeding 1000 V a.c. (root mean square) or 1500 V d.c. between conductors, or 600 V a.c. (root mean square) or 900 V d.c. between conductors and earth".
Why transposition required of low voltage power transformer winding?
It is to reduce circulating current losses on winding.
What regulations govern installation of low voltage and extra low voltage cables in the same containment and what segregation or screening is required to avoid electromagnetic or voltage crossover?
You must tell us where in the world you are located! Regulations vary from country to country and town to town.
Why consumer wants connect to high voltage?
that main resign is high voltage is voltage value is high that same time current value is very low. easy to transmission to long distance consumer(HT required consumer) end we have not voltage loss and current also and conductor cost is reduced that is conductor thickness low ,so current level is low
Why instruments are connected on low voltage side of the transformer while performing no load test?
since we need to get desired or rated voltage, so if it is connected in high voltage side of the transformer, voltage supply will be more, and hence the current will be more than the required amount. this is the reason why the instruments re connected at the low voltage of the transformer while performing no load test.
Why open circuit test is performed on low voltage side?
generally open circuit test is performed on the low voltage side.....not on high voltage side.... becuase on low voltage side, we can apply that low voltage very easily ( i.e with a less amount of source is required)... whereas on high voltage side, we need a large power source in order to apply full voltage... in short circuit test, we will test on high voltage side by keeping Low voltage side being short circuit.because high voltage side needs less current source than low voltage side....
What are the difference between high voltage and low voltage?
Hi, The main difference is Fuel consumption. High current genertors always consumes much fuel because the load on the engine will be high. The high voltage low current generators doesn't need much fuel to run. You can understand this by comparing 1 kva and 5 kva single phase generators. For both generators voltage will be same (230v) But output current differs. So the fuel consumption also differs. But you get a high current source. Low voltage high current generators can be used for welding kind of stuffs which needs high current to do the job. If you have step down transformer then you can save the fuel.
Why generally the voltage is applied to HV side?
Lower voltages are required if connected to the low voltage side. The testing facility may not have a gen set large enough to test from the high voltage side.
How many volt in low voltage?
There are three main categories of low voltage. It depends on what type of system the voltage belongs to, as each system has a bottom end or low voltage assigned to it.
