answersLogoWhite

0


Best Answer
Copy

i believe it is a 9/16 wrench, or 14/15mm if metric.

User Avatar

Wiki User

โˆ™ 2005-04-19 17:31:54
This answer is:
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
User Avatar

Add your answer:

Earn +5 pts
Q: Is there a special tool for removal of the oil pressure sending switch on a 1992 Plymouth Voyager 3.3 6 cylinder?
Write your answer...
Submit

Related Questions

How do replace the rear wiper blade on a 1999 Plymouth grand voyager?

The 1999 Plymouth Grand Voyager takes a fairly standard 18" rear wiper blade (also takes 28" replacement windshield wipers on both sides front). Additionally, the installation process is simple. The replacement wiper blades will come with step-by-step, illustrated removal and installation instructions.


How do you get to the no 1 3 and 5 spark plugs on a 1999 Plymouth Voyager?

It is a pain! Haynes manual suggests removal of drivebelt and four alternator bracket bolts to push the alternator rearward for #1. For # 3 and # 5, manual suggests removal of resonator and the intake strut bolt at the cylinder head. Next, remove the intake strut bolt and the intake manifold and swing the strut out of the way. Good luck!


What is the medical term meaning removal of pressure?

Decompression is the medical term meaning removal of pressure.


How much is involved in changing a clutch in an 1995 Chevy S10?

exhaust removal, driveshaft removal, shifter boot and shifter removal,transmission removal, removal of pressure plate and clutch disc, suggest replacing pilot bearing and replacing slave cylinder, removal and turning of flywheel, suggest replacing throw-out bearing. a full clutch kit will come with new pilot bearing, pressure plate and clutch disc, and throw-out bearing. generally a two man job


How do you replace the alternator on a 1993 Plymouth Voyager 3.3L V6?

This is hard due to limited space. Disconnect the neg. battery cable then the wiring and take the belt off and finally the mounting bolts. You have to also remove the intake manifold to have room for removal.


What size and how do you replace the dash speakers or a 1994 Plymouth Voyager?

Well I found out on my own (and the help of a few websites) that the dash speakers of a 1994 Plymouth Voyager are 5 1/4. And in replacing them I had to remove the dash trim (between the windshield and front dash),by gently prying it off with a flat head, and also the grill below the indicators. after this all screws were visible for removal. This was my first time removing a dash on any car and it was not as easy as I thought. And when putting it back on just be careful to not break the plastic and take your time.


How do you change a motor mount in a 1989 Plymouth voyager se v6 3.0L?

Well. if its your front mount, then you jack up the engine, your mount is located at the very front, at the bottom, then you remove the single bolt that goes through the mount, remove the mount, and installation is the reverse of removal.


Need removal and installation instructions for an ignition cylinder 2000 Grand Cherokee Jeep?

Need removal and installation instructions for an ignition lock cylinder -- 1999 Grand Cherokee Limited?


How do you replace the speedometer cable on a 1997 kawasaki voyager?

remove cluster and replace cable. Reverse removal procedure for installation.


What is removal ordered by the judge called?

political pressure


Remove ignition cylinder?

key switch tumbler removal on 1998 astro


How do you change a power steering pump in a 97 Plymouth voyager 3.3L?

The 1997 Plymouth Voyager came equipped in 3 powertrains including the 3.3L V6. The first steps to this install are the removal of the belts. This would also be a good time to inspect the belts for wear and replace as needed. The next steps are inspection of the high and low pressure power steering hoses, and again replacement if necessary. The next steps are disconnecting of the fluid lines from the pump assembly. The pump can then be unbolted from the engine through using a wrench. Once removed the area should be thoroughly cleaned and degreased. The new pump can then be bolted on and lines reconnected. The belt can then be reinstalled and the system purged of fluid and recharged. The OEM Mopar replacement pump for this application is #4684156AB.


Which direction is the crankshaft bolt turned for removal on a 1990 Toyota Camry 4 cylinder?

counterclockwise.


Ignition cylinder removal Volvo s70?

simply strap a piece of dynamite to the bottom and run like hell


Can removing a spark plug crack a cylinder?

Can Spark Plug Removal Crack a Cylinder?No, spark plugs screw into a threaded hole in the cylinder "heads," and therefore cannot crack a cylinder [wall around the pistons].NOTE however, that if spark plugs are not removed and reinstalled PROPERLY, this process can "strip" and ruin the threads in the cylinder "HEAD."


Installing cylinder head temperature sensor on f-250?

To install a cylinder head temperature sensor on a F-250, you disconnect the cylinder head sensor from the electrical connector at the rear of the cylinder head. When installing the new one, you reverse the process of removal. The cylinder head temperature sensor is located by the O2 sensor.


How do you change headlights on 1999 Plymouth Grand Voyager SE?

Just replaced both right and left headlight assemblies on my 1999 Plymouth Grand Voyager SE today! An abundantly easy task that merely requires the removal of 1 (one) 10mm screw which affixes the headlight assembly to the horizontal grill brace and 3 (10mm) nuts which stabilize the assembly to the headlight/radiator stabilizing panel. No need to consult any manual, the replacement job is so straightforward that even a 12 year old can do it in a mere 10 minutes each side. Suggest you purchase aftermarket units (~45.00/side) from internet source rather than pay exorbitant and outrageous prices for OEM units.


How do you change the ignition lock cylinder on your 2001 Dodge Durango?

this is for a 2002 doge durango, it must be the sameLOCK CYLINDERREMOVALThe ignition key must be in the key cylinder for cylinder removal.# Disconnect negative cable from battery. # Remove upper and lower covers (shrouds) from steering column. # Place shifter in PARK position.# A retaining pin (Fig. 9) is located at side of key cylinder assembly. # Rotate key to RUN position. # Press in on retaining pin while pulling key cylinder from ignition switch.INSTALLATIONThe ignition key must be in the key cylinder for cylinder installation.# Install the key cylinder into the housing using care to align the end of the key cylinder with the ignition switch. # Push the key cylinder in until it clicks. # Replace the upper and lower shrouds. # Reconnect the battery.


How do you replace the first cylinder on a 2002 Saturn SL?

removal of one cylinder is EXTREMELY odd and probally not needed. To do the head must come off, timing chain, oil pan, and crankshaft


Where is the slave cylinder on 1990 Ford Ranger?

It should be around the pilot shaft on the trans. It requires removal of the trans to replace it.


How do you replace Blower motor on 1996 Plymouth Voyager?

Remove the glove box then the four (4) hex screws on the blower motor cover. Then remove the mounting screws for the blower motor and set it down on the floor - it should have enough length in the wiring. Disconnect the the wiring connector them remove the rubber grommet and wiring harness through the blower housing. Installation is the reverse of removal. Good luck!


Where is the oil pressure sending unit located on a 1995 Chevy K-1500 305?

The oil pressure sending unit is located under the hood, way in back of the engine, under the distributor on the drivers side. Removal requires removal of the distributor.


Ignition lock cylinder removal on a 94 ford escort?

How to remove and replace ignition lock on 94 escort lx wagon1.9


Water pump removal f150 1995 ford 6-cylinder?

The belt needs to be removed. The fan will have to be unbolted and removed, you may have to remove the fan shroud as well. The water pump can then be unbolted and changed.


How do you remove the clutch master cylinder hose from the transmission case on a 1994 ford ranger?

This is a quick release and needs a clutch coupling removal tube T88T-70522-A or equivalent. Slide the sleeve toward the slave cylinder while pulling the tube away from the slave cylinder.