Yes
It is an oblong switch under the dash NEAR the driver's left knee.
1. With all doors closed and the ignition switch in any position except On or Start, buckle the driver's seat belt. 2. Turn the ignition switch to the ON position and wait for the Seat Belt Warning Light to turn off. 3. Within 60 seconds of turning the ignition switch to the ON position, unbuckle and then re-buckle the driver's seat belt at least three times within 10 seconds, ending with the seat belt buckled. NOTE: Watch for the Seat Belt Warning Light to turn on while unbuckling and off while re-buckling the seat belt. It may be necessary to retract the seat belt. 4. Turn the ignition switch to the LOCK position. A single chime will sound to signify that you have successfully completed the programming.
1. With all doors closed and the ignition switch in anyposition except On or Start, buckle the driver's seat belt.2. Turn the ignition switch to the ON position and waitfor the Seat Belt Warning Light to turn off.3. Within 60 seconds of turning the ignition switch to theON position, unbuckle and then re-buckle the driver'sseat belt at least three times within 10 seconds, endingwith the seat belt buckled.NOTE: Watch for the Seat Belt Warning Light to turn onwhile unbuckling and off while re-buckling the seat belt.It may be necessary to retract the seat belt.4. Turn the ignition switch to the LOCK position. Asingle chime will sound to signify that you have successfullycompleted the programming.1. With all doors closed and the ignition switch in anyposition except On or Start, buckle the driver's seat belt.2. Turn the ignition switch to the ON position and waitfor the Seat Belt Warning Light to turn off.3. Within 60 seconds of turning the ignition switch to theON position, unbuckle and then re-buckle the driver'sseat belt at least three times within 10 seconds, endingwith the seat belt buckled.NOTE: Watch for the Seat Belt Warning Light to turn onwhile unbuckling and off while re-buckling the seat belt.It may be necessary to retract the seat belt.4. Turn the ignition switch to the LOCK position. Asingle chime will sound to signify that you have successfullycompleted the programming.
It means someone does not have their seat belt on. If you have any packages sitting on a seat they may be triggering the switch. If you don't you may have a bad seat switch.
Check with your dealer. Seems to me that there was a recall or service bulletin on the driver's seat belt.
Probably, but the defense will argue that the passenger contributed to his injuries by not wearing the seat belt which the driver provided.
First option is obeying the law and wearing your seat belt. Second option The Enhanced Warning System (BeltAlert) can be enabled or disabled by your authorized dealer or by following these steps: NOTE: The following steps must occur within the first 60 seconds of the ignition switch being turned to the ON or START position. DaimlerChrysler does not recommend deactivating the Enhanced Warning System (BeltAlert). 1. With all doors closed and the ignition switch in any position except On or Start, buckle the driver's seat belt. 2. Turn the ignition switch to the ON position and wait for the Seat Belt Warning Light to turn off. 3. Within 60 seconds of turning the ignition switch to the ON position, unbuckle and then re-buckle the driver's seat belt at least three times within 10 seconds, ending with the seat belt buckled. NOTE: Watch for the Seat Belt Warning Light to turn on while unbuckling and off while re-buckling the seat belt. It may be necessary to retract the seat belt. 4. Turn the ignition switch to the LOCK position. A single chime will sound to signify that you have successfully completed the programming. The Enhanced Warning System (BeltAlert) can be reactivated by repeating this procedure. NOTE: Although the Enhanced Warning System (BeltAlert) has been deactivated, the Seat Belt Warning Light will continue to illuminate while the driver's seat belt remains unbuckled.
The following steps must occur within the first 60 seconds of the ignition switch being turned to the ON or START position. DaimlerChrysler does not recommend deactivating the Enhanced Warning System (BeltAlert). 1. Turn the ignition switch to the LOCK position and buckle the driver's seat belt. 2. Turn the ignition switch to the ON position and wait for the Seat Belt Warning Light to turn off. 3. Within 60 seconds of turning the ignition switch to the ON position, unbuckle and then re-buckle the driver's seat belt at least three times within 10 seconds, ending with the seat belt buckled. NOTE: Watch for the Seat BeltWarning Light to turn on while unbuckling and off while re-buckling the seat belt. It may be necessary to retract the seat belt. 4. Turn the ignition switch to the LOCK position. A single chime will sound to signify that you have successfully completed the programming. The Enhanced Warning System (BeltAlert) can be reactivated by repeating this procedure.
The Enhanced Warning System (BeltAlert) can be enabled or disabled by your authorized dealer or by following these steps: NOTE: The following steps must occur within the first 60 seconds of the ignition switch being turned to the ON or START position. 1. Turn the ignition switch to the OFF position and buckle the driver's seat belt. 2. Start the engine and wait for the Seat Belt Warning Light to turn off. 3. Within 60 seconds of starting the vehicle, unbuckle and then re-buckle the driver's seat belt at least three times within 10 seconds, ending with the seat belt buckled. NOTE: Watch for the Seat BeltWarning Light to turn on while unbuckling and off while re-buckling the seat belt. It may be necessary to retract the seat belt.
if the ignition is cycled, driver's seat belt is unbuckled for more than 10 seconds and the vehicle speed is greater than 5 mph (8 km/h). The Enhanced Warning System (BeltAlert) can be enabled or disabled by your authorized dealer or by following these steps: NOTE: The following steps must occur within the first 60 seconds of the ignition switch being turned to the ON or START position. DaimlerChrysler does not recommend deactivating the Enhanced Warning System (BeltAlert). 1. With all doors closed and the ignition switch in any position except On or Start, buckle the driver's seat belt. 2. Turn the ignition switch to the ON position and wait for the Seat Belt Warning Light to turn off. 3. Within 60 seconds of turning the ignition switch to the ON position, unbuckle and then re-buckle the driver's seat belt at least three times within 10 seconds, ending with the seat belt buckled. NOTE: Watch for the Seat Belt Warning Light to turn on while unbuckling and off while re-buckling the seat belt. It may be necessary to retract the seat belt. 4. Turn the ignition switch to the LOCK position. A single chime will sound to signify that you have successfully completed the programming. The Enhanced Warning System (BeltAlert) can be reactivated by repeating this procedure. NOTE: Although the Enhanced Warning System (BeltAlert) has been deactivated, the Seat Belt Warning Light will continue to illuminate while the driver's seat belt remains unbuckled.
Disconnect electrical connector under driver seat that connects to seat belt device.
To switch out a seat belt usually the seat needs to be removed first. Then it is in most instances just a bolt to be removed.