0
Is your baseboard heater using power when a single-pole thermostat is set to low?
Wiki User
∙ 13y ago
Your thermostat is just a temperature switch. A switch just breaks the circuit to stop the current from flowing. When you set a position on the thermostat you are telling the switch when to come on and when to shut off depending on the room temperature. If it is set to low then the base board heater will not come on until the low set-point is reached. When the room warms up to above the set-point the baseboard heater will shut off. If your concern is about a 240 volt baseboard heater and just a single pole on the thermostat do not worry. Breaking one leg of a 240 volt circuit will stop the current flow and the heater will not operate.
Wiki User
∙ 13y ago
Add your answer:
Earn +20 pts
How many BTU per hour is a 1500 watt heater?
Answer1 kW is 3,413 BTUs. Therefore, 1500 Watts = 1.5 kW and 1.5 kW x 3413 BTU/kW = 3 413 * 1.5 = 5 119.5 BTUs per hr for a 1500 Watt heaterwhat is the electric cost/
What is electric water heater which used in house?
An electric water heater in a hot tank is called an immersion heater and many of those run at 3 kW with a thermostat to control the max temperature. Power showers use a type of water heater that heats the water at the point where it is used, without a tank. They run at 6-8 kW and are also controlled by a thermostat.
Why is it important that the resistance of an extension cord used to power an electric heater be kept low?
An electric heater is one of the high-power appliances in a house, commonly taking 1.5 to 3 kilowatts of power. The current is high, and therefore there is a drop in the voltage applied to the heater equal to the current multiplied by the resistance of the cord. There is probably little power wasted, because any heat from the cord goes to heat up the same room. But a voltage drop causes the heater to draw less current because its resistance is constant, and therefore less total power is provided to heat the room. If the heater is thermostatically controlled so that it is not working all the time, the difference is small because any reduction in the heater's power would cause the thermostat to keep it going for longer, to compensate.
Only electric thermostat what color is the power wire?
Red
Can a bad element in a water heater cause absurdly high electric bills?
Bad elements consume no power. A malfunctioning water heater could cause high utility bills if it is heating for long periods because the thermostat has failed and does not switch off the current when the set temperature has been reached. You should see some signs of this as in very hot water!
How do you wire a single pole built in thermostat to a baseboard heater while feeding power to another thermostat?
Split the feed circuit (inside a junction box) and feed the hot to both the baseboard heater with the built in thermostat AND to the 2nd thermostat. If you have any questions, contact a local, qualified electrician, heating specialist or local handyman.
Is there a switch available to control power to a thermostat for 20A 240V electric baseboard heater?
There are two types of thermostats. One is a line voltage stat. This is in effect a switch and when turned to the off position the voltage is interrupted and the heater will not operate. The other type of stat is low voltage. There will be a relay in the baseboard heater that the thermostat is connected to. With this type if installation to turn the power completely off you will have to turn the breaker off that feeds the circuit.
If a baseboard heater has its own thermostat can you bypass it and wire it to a wall mounted thermostat?
Yes, but be sure you buy what is known as a `line voltage thermostat`when you do this since you have no control voltage but are simply breaking a line in the main power feed to turn the strip on and off.
How do I turn off a baseboard heater when there is no visible thermostat?
There is a thermostat somewhere, usually on the wall or on the heater itself. Just turn the breaker off at the breaker box. Label the breaker if it is not already labeled. Once the power is turned off to the unit, you can disconnect the wires inside the heater to permanantly shut down the unit.
How do you wire a double pole thermostat to two baseboard heaters?
This is wiring 2 baseboard heaters with a double pole wall thermostat you run the power wire to the thermostat on the wall then you run a wire to the 1st heater and then you run another wire from the 1st heater to the 2nd heater and hook red on red and black on black with wiring mariette's in the heaters junction box on left or right side which ever is more suitable for you and then you go to the wall thermostat and hook red on red and black on black with the wiring mariette's and then you hook your power wire to the power supply which is 100 or 200 amp service and on a double 20 breaker and the wire has to be no smaller than 12/2 wire. also do not forget to hook the ground wire (bare copper) on the green screw on your heater and in the thermostat box and then on the power supply box..... now you can turn up your thermostat and enjoy the heat ...........LEE48
What does a thermostat do and how does a thermostat work?
the thermostat used to control the heater and after we select the four pole switch to some number the thermostat start connect the power to the heater at the same time the heater start to heat and when we select the switch to zero position the heater not work
How do you wire two baseboard heaters to one thermostat?
you run the power wire to the thermostat on the wall then you run a wire to the 1st heater and then you run another wire from the 1st heater to the 2nd heater and hook red on red and black on black with wiring mariette's in the heaters junction box on left or right side which ever is more suitable for you and then you go to the wall thermostat and hook red on red and black on black with the wiring mariette's and then you hook your power wire to the power supply which is 100 or 200 amp service and on a double 20 breaker and the wire has to be no smaller than 12/2 wire. also do not forget to hook the ground wire (bare copper) on the green screw on your heater and in the thermostat box and then on the power supply box..... now you can turn up your thermostat and enjoy the heat ...........LEE48
How do you fix an electric baseboard heater?
first of all you buy a double pole unit thermostat which should come with the mounting plate and thermostat and it should have 4 wires 2 red 2 black okay now you join the red to the red power wire and black to the black power wire and the 2 remaining wires which should be a red and black can be joined to the red and black wires on your heater .....now you should be good to go ............LEE48
What is the difference between a single pole breaker and a double pole breaker?
Courtesy of Ace Hardware - I found it on their site · What is the difference between a double pole and a single pole thermostat?Single pole thermostats breaks only one side of the power line to your heater and cannot be turned off. Therefore, power is continuous to the heater even if it is not running. The control knob will have a low temperature setting without an off position. Single pole Thermostats uses only two wires. This means that even if the temperature dial is turned all the way down, voltage is still going into the heater through one line. This may pose a hazard to anyone who might perform electrical work on the heater without realizing that the circuit was still on. You will need to turn off the power at the circuit breaker before electrical repairs can be made safely.Double pole thermostats breaks both sides of the power line; therefore all power to the heater is interrupted. This acts as a safeguard for people performing electrical work on the heater. However, to be on the safe side, you should always turn off the power at the circuit breaker, not at the thermostat, before making any electrical repairs. A double pole will uses four wires and has a off position on the thermostat.Since they are inherently safer, you should always try to use double-pole thermostats, if possible. Another advantage of a double-pole thermostat is that you can turn it completely off and the heat will not come on no matter how cold your room gets. But with a single-pole unit, the thermostat will turn the heat on even if set on the lowest setting.CHECK YOUR LOCAL CODES FOR BUILDING REQUIREMENTS IN DETERMINING IF YOU NEED A SINGLE OR DOUBLE POLE THERMOSTAT BEFORE PURCHASING OR INSTALLING. How can I determine if I have a single or double pole thermostat?Usually, you can tell the difference between a single pole and double-pole thermostat by looking at the dial. A double-pole normally has an "Off" position on the dial whereas a single-pole thermostat does not. The only sure way to tell which kind you have is to remove it from the wall and count the wires connected to it. A double-pole thermostat will have four wires that switches both hot wires whereas a single-pole thermostat will have two wires that only switches one of the hot wires. Can I use a single or double pole thermostat with a 120, 208, or 240 volt heater?Yes. Can I use 1 thermostat to control more than 1 baseboard heater?Built-in thermostats (mounted directly on baseboard) are designed for single heater use. However, it is possible to control more than 1 heater on a wall thermostat if the thermostat rating is not exceeded. Can I mount the thermostat on one side and wire the baseboard heater on the opposite side?No, the thermostat requires power from the supply wires and must be wired in conjunction with the baseboard heater. Is a built-in or a wall mount thermostat better?A built-in control is convenient when the walls are already finished. The built-in thermostat is also convenient to install. However, the wall thermostat is a more accurate way to control the room temperature, is more convenient to use, and has a broader selection of models. The use of electronic thermostats provides more accuracy and saves you money on your electric bill. Can all of the heaters in my house be controlled by one thermostat?There are many benefits to zonal heating. Zonal systems save energy by not heating unoccupied rooms and provide the ultimate in comfort by allowing occupied zones to be heated specifically to individual needs. The purpose of each zone's (room) heater is to heat that specific zone per the set point of the individual thermostat. What is the difference between a low voltage and a line voltage thermostat?Low voltage thermostats should be used when the heater load is greater than 3,800 watts such as commercial heater or central forced air systems.Line voltage thermostats should be used for zonal heat systems such as electric fan heaters, baseboard heaters and radiant heaters. What should I do if my wall thermostat feels hot to the touch?Cadet recommends you replace the thermostat. A hot thermostat indicates that it is not working efficiently; decreasing its accuracy. NOTE: A normal operating thermostat will be slightly warmer than the room temperature by 3 to 5 degrees. Can I use a wall mount thermostat to control my heater if it has an in-built thermostat?Yes, to bypass the in-built thermostat, turn the thermostat on the heater to the highest setting, then use the wall thermostat to regulate the room temperature.
How does someone install a Honeywell thermostat?
Disconnect all power sources to your existing thermostat. Remove the cover. Locate wire connecting thermostat and heater. Not the terminal designations. Disconnect wiring to heater. Remove old thermostat from wall. Drill holes for mounting new thermostat. Connect wires. Attach subbase of new thermostat to wall. Connect wires, matching labels. Attach thermostat to subbase.
How many BTU per hour is a 1500 watt heater?
Answer1 kW is 3,413 BTUs. Therefore, 1500 Watts = 1.5 kW and 1.5 kW x 3413 BTU/kW = 3 413 * 1.5 = 5 119.5 BTUs per hr for a 1500 Watt heaterwhat is the electric cost/
How do you know what the voltage of your electric baseboard heater is if there is no label on the heater?
Go to your power panel and look for two pole breakers. If there are any 20 amp two pole breakers there is a good chance that they are for the baseboard heaters. Switch this breaker off and turn your thermostat up. If the baseboard heaters do not come on and get hot then this is the supply for them. A two pole breaker is supplying 240 volts to the heaters. Most likely there will be more that one heater on the circuit. As always, if you are in doubt about what to do, the best advice anyone should give you is to call a licensed electrician to advise what work is needed.Before you do any work yourself,on electrical circuits, equipment or appliances,always use a test meter to ensure the circuit is, in fact, de-energized.IF YOU ARE NOT ALREADY SURE YOU CAN DO THIS JOBSAFELY AND COMPETENTLYREFER THIS WORK TO QUALIFIED PROFESSIONALS.
