0
Want this question answered?
Be notified when an answer is posted
Add your answer:
Earn +20 pts
For voltage drop calculation you must use the current of the circuit breaker or the normal currents?
For voltage drop calculation you must use the current of the load and the distance of the load from the supply source. The circuit breaker is then used to limit the current to the rating of the wire that feeds the load.
What is the cause of failure of foundation of a building?
The foundation of a building may fain in shear or due to excessive settlement. if the load on the foundation is more than the bearing capacity of soil or the settlement due to the load is more than tne allowable limit than the foundation is said to fail.
What is metal fatigue and what is thought to cause it?
Stress of a steel beam, for example, which can overload and bend eventually, if the load on the beam is greater than the design limits of that beam.Heat can also stress metal to the point of changing shape, losing strength and becoming brittle enough to fracture.2nd AnswerThe above answer is actually describing a load that exceeds the materials ultimate stress. Fatigues does not cause the part to bend.Stress is a repeated application of a load that is below the ultimate design load that results in microscopic distortion of the metal and can induce cracks. These cracks will eventually grow under repeated load applications and resulting in failure of the part.All material is tested for its fatigue Endurance Limit. If you design the part so that it will have repeated loads below this Endurance Limit OR design it so that it does not see high cycles of load application, then the part can be designed so that it will not fatigue.
How does a 1 in 100 gradient limit a locomotives load?
1 in 100 gradient = 1% incline or a rise of 1ft per 100 ft of travel. To understand how this limits a locomotive load try carrying a bundle of roof shingles 100 ft on level ground, then climb a 100 ft ladder with them.
Bear the load or bare the load?
Bear the load. Bare the load would be to uncover the load...
The load limit on a small bridge is 8 ton what is the load limit in pounds?
What are the basis of a bridge load limit?
How do you calculate working load limit?
There are several ways to calculate working load limit. One of these includes Minimum Breaking Load (MBL) divided by Working Load Limit (WLL) equals Working Load Limit (WLL).
What is load limit governor?
A load limit governor is a device that is controls the amount fuel that goes to the engine. This ensures that the amount of fuel that goes into the engine is not above the specified limit.
Where does a capacity plate indicate?
Safe load limit
Why load resister is conected across the circuits?
Load resistors are connected across the circuit to limit the current flowing through the load.
How do you get the aggregate working load limit for a commercial motor vehicles?
I've never heard of an aggregate working load limit for a vehicle. The only place that term is used in the Federal Motor Carrier Safety Administration Reglations is in the load securement section. If that is what you meant, it's pretty simple. Most tiedowns and chains should be marked with their Working Load Limit. If they are, you simply add them up. Five synthetic straps with Load Limits of 7,000 pounds each equals an aggregate working load limit of 35,000 pounds. In most cases, your aggregate working load limit must be at least 50% of the total weight of what you are carrying. In this case, these 5 tiedowns' load limit would be enough for something weighing 70,000 pounds. If you don't know what the Load Limits are, you can go to 393.108 in the regulations. They have a list of tiedown types and sizes. If the tiedown is not marked, you must use the assigned rating from the regs. You need to check 393.100 through 393.136 though. Many commodities, such as bundled lumber, vehicles, heavy equipment, have specific requirements in addition to the genereal load limit requirements. Also, keep in mind, if you are inspected and your load is not secured sufficiently, it is an Out of Service Violation and you can probably count on being issued a ticket, being parked where you are, and your company's safety rating going down." That is not quite right. According to the rules the aggregate working load limit is "the sum of one half of the working load limit of each tiedown". This means you divide the load rating of each tiedown by two and then add them up to get the aggregate working load limit. If your tiedowns are rated at 7,000 lbs and you have 5 tiedowns , the aggregate working load limit, the sum of one half of the working load limit of all tiedowns would be 17,500 lbs. Securment rules state "The aggregate working load limit of any securement system used to secure an article or group of articles against movement must be at least one-half the weight of the article or group of articles". Divide the working load limit of each tiedown used by two and add them together. This number needs to be equal to or greater than half the weight of your load. It is an overcomplicated, fancy way of saying that the load limit of your tiedowns must be equal to the weight of the load.
What is a suzuki every minivan?
The Suzuki Every Minivan is a multi-purpose minivan.
How would you use load in a sentence?
I will load the car. The truck's load is too heavy. Load the wheel barrow with plants. The load limit is 4,000 lbs. per axle.
What would you use to measure a load limit of an elevator with?
tons
What is limit load factor in aviation?
the maximum load factor without structural damage to the aircraft. Load factor = 1 / (cos (angle of turn))
How many feet long is a minivan?
It depends on the minivan.
Does a minivan transform into a robot?
G1 Skids is a minivan, and so is RID X-Brawn, the brother of Prowl and Sideburn. G1 Ironhide also Transforms into a minivan. So technically, no. A minivan can not turn into a robot, but a Transformer robot can turn into a minivan.
