0
For voltage drop calculation you must use the current of the circuit breaker or the normal currents?
Wiki User
∙ 15y ago
For voltage drop calculation you must use the current of the load and the distance of the load from the supply source. The circuit breaker is then used to limit the current to the rating of the wire that feeds the load.
Wiki User
∙ 15y ago
Add your answer:
Earn +20 pts
Rupturing capacity of a circuit breaker?
the maximum short current that can be safely break by the circuit breaker.
What is a difference between 10KA and 22KA circuit breakers?
The previous answer is incorrect, and I would advise that user to not give out information if they are going to give completely misguided information. The interrupting rating of a breaker is the maximum current that the breaker is designed to handle, at the breaker's rated voltage, before damage will occur to the breaker. A breaker will trip at FAR LESS than the interrupting rating, but it is extremely dangerous to expose the breaker to any situation where it will have more than the rated interruption current. the breaker is designed for. The reason some breakers are rated at 22kA instead of 10kA is because they typically have far larger conductors hooked up to them, so with the lowered impedance on the circuit there is more of a chance for the breaker to experience a higher fault current at the breaker. So electricians install 22kA breakers to handle the higher "available fault current."
What is different Circuit Breker And Isolater?
I think that the questioner is asking what is the difference between an isolator and a circuit breaker.A circuit breaker is a switching device designed to interrupt a fault current.An isolator is not intended to break a live circuit but, rather, to provide a visible separation between a circuit component and live conductors.For example, isolators (or 'disconnectors' in US parlance) are located on either side of a high-voltage circuit breaker. If the circuit breaker requires maintenance, then the procedure is to:a. trip the circuit breaker.b. open the isolators on each side of the circuit breaker, so there is a visible gap between the circuit breaker and the 'hot' conductors.c. apply temporary earths (grounds) between each isolator and the circuit breaker.d. complete a 'permit to work' card.e. begin work.
Will a circuit breaker function properly if it is back fed?
Yes. The circuit breaker "does not care" which direction the current comes from. It is capable of protecting the circuit in any case.
What do circuit breakers and fuses have in common?
Both fuses and circuit breakers cut off a circuit from its power supply when the total current through the circuit exceeds the current rating of the fuse or circuit breaker, usually due to a short to ground or overloading of the circuit. Both use materials that respond to heat.
Is a circuit breaker a resistor?
No, a circuit breaker is a safety device that is used in a circuit to limit the amount of current in an overload or short circuit condition. The number on a breaker is the top end current that the breaker will handle before opening the circuit.
What is Ir value of a circuit breaker?
Ir is the Interrupt rating of the circuit breaker. It is the maximum amount of current the breaker can withstand without damage. In a molded case breaker's electronic trip mechanism, Ir is the continuous current rating that you select, to trip the breaker at a given overload current. Standard requirements request that the breaker trips at 2 hours with an overload of 135% and will trip as a function of I squared x time selected for higher currents.
Will a circuit breaker give off less amperage?
A circuit breaker does not give off amperage. A circuit breaker allows a flow of current up to the rating of the breaker. Any current higher than that of the breaker's rating will open the breaker's contacts and stop the flow of current.
Rupturing capacity of a circuit breaker?
the maximum short current that can be safely break by the circuit breaker.
What is a rccb?
A residual-current device (RCD), or residual-current circuit breaker (RCCB), is an electrical wiring device that disconnects a circuit whenever it detects that the electric currents not balanced between the energized conductor and the return neutral conductor.
What is rccb?
A residual-current device (RCD), or residual-current circuit breaker (RCCB), is an electrical wiring device that disconnects a circuit whenever it detects that the electric currents not balanced between the energized conductor and the return neutral conductor.
When dangerously high currents flows through a thin strip of metal melts which creates an open circuit and current stops flow?
This is the general description of how a circuit breaker operates.
What is a difference between 10KA and 22KA circuit breakers?
The previous answer is incorrect, and I would advise that user to not give out information if they are going to give completely misguided information. The interrupting rating of a breaker is the maximum current that the breaker is designed to handle, at the breaker's rated voltage, before damage will occur to the breaker. A breaker will trip at FAR LESS than the interrupting rating, but it is extremely dangerous to expose the breaker to any situation where it will have more than the rated interruption current. the breaker is designed for. The reason some breakers are rated at 22kA instead of 10kA is because they typically have far larger conductors hooked up to them, so with the lowered impedance on the circuit there is more of a chance for the breaker to experience a higher fault current at the breaker. So electricians install 22kA breakers to handle the higher "available fault current."
What is a switch that opens a cuircut when too much current is flowing?
Where I'm from, it's called a "circuit breaker".A circuit breaker.
What is a switch that automatically opens if a current is too high?
Where I'm from, it's called a "circuit breaker".A circuit breaker.
What is switch that automatically opens if the current is too high?
Where I'm from, it's called a "circuit breaker".A circuit breaker.
Why does an electrical breaker trip when you use a lot of appliances in the house?
since circuit breaker consists of coils they get heated up when high current flows, when this happens the coil get energised and pull the moving contacts to open thus the circuit breaker opens when high current flows.
